2003 ACCESSORIES & EQUIPMENT Wiper & Washer Systems – Baja, Legacy & Outback REAR WIPER ARM
Removal 1. Raise wiper arm cover (A). 2. Loosen nut to remove wiper arm.
INSTALLATION 1. Install in the reverse order of removal. 2. Operate rear wiper once. 3. Align blade to rear defogger heat wire (A).
Tightening torque: Refer to FRONT WIPER , COMPONENT, General Description.
Whether your an expert Subaru Legacy car alarm installer, Subaru Legacy performance fan or a novice Subaru Legacy enthusiast with a 1997 Subaru Legacy , a Subaru Legacy car alarm wiring diagram can save yourself a lot of time. One Subaru Car Alarm Wire Diagrams of the most time consuming tasks with installing an after market car alarm, car security, car remote start, automatic remote starter, shock sensor, tilt sensor, car alarm sensor or any auto alarm is identifying the correct color car security Rochester Auto Search wires for a 1997 Subaru Legacy. The Modiﬁed Life staff has taken all its Subaru Legacy car alarm wiring diagrams, Subaru Legacy car security wiring diagrams, Subaru Legacy car alarm wire diagrams, Subaru Legacy car security wiring schematics, Subaru Legacy car security diagrams, Subaru Legacy remote Read more
Wiper and Washer System — Exploded View Front Wiper System 1 17526 RH/ Wiper pivot arms required) (part of wiper motor 17527 LH assembly) 2 022A68 RH/ Cowl grille panel 7 — Wiper pivot arm (part of 022A69 LH wiper motor assembly) 3 W703845 Windshield wiper mounting 8 17508 Windshield wiper motor arm and pivot shaft assembly bolts (3 required) 4 17508 Pivot shaft assembly 5 — Windshield wiper motor bolts Read more
Relay arrangements on the relay panel – Dual Horn Relay (53) 1- Load Reduction Relay (213, 100, 18) 2 – open 3 – Fuel Pump (FP) Relay (409) 4 – Wiper/Washer Intermittent Relay (377), V Wiper/Washer Intermittent Relay (377), VI Fuse placements on the relay panel A- Fuse for power windows (red connector) B- open C – Fuse for heated power seats (black connector)
1997 Subaru Legacy GT Sedan AWD F4-2.5L DOHC Vehicle Level Engine, Cooling and Exhaust Engine Timing Belt Service and Repair Installation INSTALLATION SPROCKET 1) Install right-hand belt cover No.2. 2) Install left-hand belt cover No.2. 3) Install tensioner bracket 4) Install crankshaft sprocket. 5) Install right-hand exhaust camshaft sprocket. To lock camshaft, use ST. 6) Install right-hand intake camshaft sprocket using ST. 7) Install left-hand exhaust camshaft sprocket using ST. Install left-hand intake camshaft sprocket using ST.
Paciﬁc Western Design 53/54 Chevrolet Wiper System is designed to install in cars which are modiﬁed to use a 12- volt negative ground electrical system only and is not available for 6-volt(original)cars.
Congratulations on the purchase of the new AccessPORT handheld programmer. The AccessPORT can: ● Reprogram the factory engine control unit (ECU) with improved tuning parameters through the on-board diagnostic (OBD-II) port ● Monitor vehicle sensor data using on-screen analog or digital gauges ● Read and clear engine diagnostic trouble codes (DTCs) ● Measure 0-60 and ¼ mile times* ● Monitor current and averaged fuel economy* ● Calculate current estimated horsepower and torque*
Supported Vehicle List ● 2004 – 2006 Subaru Impreza STI** ● 2005 – 2006 Subaru Legacy GT (MT & AT)** ● 2005 – 2006 Subaru Outback XT (MT & AT)** ● 2004 – 2006 Subaru Forester XT (MT & AT)** ● 2006 Subaru Impreza WRX (MT & AT)**
Layout Of Rear Power Distribution Box Fuse Assignments : Fuse Assignments: 1 To 4 Door Lock – Fuel Injector Fuel Injector – Ignition Coil Ignition Coil – Park Brake Park Heating – Seat Lumber Seat Lumber – Trunk Lock Underhood – Wiper Component Index
REMOVAL OF ORIGINAL SPLASH PAN Raise and safely support the vehicle on jack stands or on ramps. Locate and remove the two 12mm bolts at the rear of the factory splash pan. Locate and remove the two 10mm screws from the left and right side of the factory splash pan. These are located up inside the fender. Locate and remove the three remaining 12mm bolts from the front of the factory splash pan. The splash pan has retaining tabs around the three bolt holes from the last step and will require some downward force to remove the splash pan from the vehicle
A screech or whine from the rear differential when making a tight turn at low speed (for example, in a parking lot when 4WD engages).
The differential fluid is contaminated or broken down, providing insufficient lubrication.
Replace the dual pump fluid, and test-drive the vehicle. If necessary, replace the rear differential clutch, replace the oil pump assembly (1997 model only), and add a flow collar.