70-2054 General Motors Amplifier Bypass Harness Instalation Instructions
RPO codes tell what options & accessories a vehicle has. RPO codes can be found in the glove box, on the trunk lid or hatch, or on the drivers side door jam near the latch. If you find the RPO code & it does not match one listed above for your particular vehicle, you should not use this harness.
Many factory amplifiers are now incorporating the crossovers for the tweeters and subwoofers within the amplifier. When bypassing the factory amplifier, you need to cross over those speakers with either passive crossovers or use an after-market AMP with built in crossovers.
Read more
556H Honda/Acura Immobilizer Bypass Module
The Honda/Acura Immobilizer anti-theft system uses a low-power transponder mounted in the head of the ignition key. When the vehicle is started, the Key Cylinder Module converts the transponder signal and sends a secure, coded signal to the Engine Control Module. If the signal to the Engine Control Module is correct, the vehicle will start.
Read more
1982-02 General Motors J-2000 Panel-Style Factory Head Unit Provisions
For BUICK Century 1982-96 Disconnect the negative battery terminal to prevent an accidental short circuit. Remove (4) screws from the top-inside edge of the dash trim bezel. Remove (5) screws from both sides of the steering column. Remove (3) Phillips screws securing the rocker-switch housing and lift the housing out. Remove the bezel. Remove the hardware securing the factory mounting brackets to the factory head unit. Remove and retain the brackets. Skip to the Installation Instructions for ALL VEHICLES on Page #34.
Read more
1997-2003 Buick Regal Engine Compartment Fire Recall Bulletin
General Motors has decided that a defect, which relates to motor vehicle safety, exists in certain 1997-2003 model year Buick Regal and Pontiac Grand Prix, 1998-1999 model year Chevrolet Lumina and Oldsmobile Intrigue, 1998-2003 model year Chevrolet Monte Carlo, and 2000-2003 model year Chevrolet Impala model vehicles, equipped with a 3.8L V6 naturally Read more
1995 Buick Regal V6-231 3.8L VIN L SFI – HVAC Blower Motor
HVAC Blower Motor Noise/Vibration
(Install New Blower Motor Assembly and/or VP Lower Compartment Access Hole Cover)
Models:
1995-96 Buick Regal
1995-96 Oldsmobile Cutlass Supreme
1994-96 Pontiac Grand Prix
Condition
Some owners may comment on noise and/or vibration from the HVAC blower motor.
This noise/vibration may be due to the blower motor being out of balance, or contents
(i.e. tissues, papers, etc.) in the instrument panel (I/P) lower compartment being drawn
into the blower motor assembly through the re-circulation door during MAX A/C mode.
Read more
External and Internal Bypass Fuel Pumps Installation Instructions
These instructions must be read and understood fully before beginning installation. Failure to follow these instructions may result in poor performance, vehicle damage or personal injury. If these instructions are not fully understood, installation should not be attempted. Please consult with BLP Technical Services or a qualified engine builder.
Read more
1996-2000 Audi A4 Short Throw Shifter Installation Instructions
This B&M Short Throw Shifter has been designed to work on most 1996-2000 Audi A4, 2000 Audi S4, 2000 Audi A6, and 1996-2000 Volkswagen Passat models. It has been engineered to greatly reduce shift throw and improve shifter feel. Check the parts and tools lists at the beginning of these instructions for the supplied parts and the tools required to install your B&M Short Throw Shifter. Installation of the B&M Short Throw Shifter can be accomplished by anyone with minimal mechanical experience.
Read more
1996-2000 Civic CX/DX/LX Cold Air System Installation Instructions
Read and understand these instructions BEFORE attempting to install this product.
1) Disconnect the negative battery terminal.
2) Make sure the engine is cool enough to drain coolant from the radiator.
3) Raise the vehicle and support on properly rated jackstands. a) Remove the front lower splash shield. (Fig 1) b) Loosen the passenger-side fender well liner and move sufficiently to gain access to the area immediately behind the front bumper. This is where the air filter is going to be installed. (Fig 2)
Read more
Transponder Bypass for Honda ET Acura (2 programmable modes)
You must use the Black key to complete the programming procedure. Programming : Keep the programming button pressed down while inserting the wire harness into connector of the HONDA-DA. Release the programming button once the LED turn ON. Turn the Ignition to the ON position. The number of LED flashes indicates the mode. (I.e. Mode 1 = 1 Flash) Press the programming button to switch between modes 1, 2 and 3. (Mode 3 is future use) Once the mode is selected, turn the ignition key to OFF position. Turn the IGNITION key to the ON position once again. The LED will illuminate. The module is now programmed. Turn the key to the OFF position and remove it, start the vehicle using the remote starter to insure functionality.
Read more
GM-T100 Transponder/Passlock II Bypass Module Installation Procedures
If multiple relays or devices are connected to the Ground Out When Running wire of the remote starter, ensure they are all diode isolated in order to avoid feedback and damaging the vehicle. Do not connect to the GOWR in the back of the remote starter when using multiple device or relays.
Read more
