2006-2009 Toyota Camry Harsh 5-4 Downshift on Deceleration
Some 2006 – 2009 model year Camry vehicles equipped with the 2AZ-FE engine and U250E automatic transaxle (ATM) may exhibit a harsh 5–4 downshift under the following conditions: • ATM at normal operating temperature • After driving above 45 mph (72 km/h) • Decelerating through 28 mph (45 km/h) The line pressure control solenoid assembly (SLT) has been improved to reduce this condition on customer complaint vehicles.
Read more
2004 Toyota Camry L4-2.4L Front Brake System
This document cover the installation of front brake for Toyota Camry:
OVERHAUL HINT: Overhaul the RH side by the same procedures with LH side.
1. REMOVE FRONT WHEEL
2. DRAIN BRAKE FLUID NOTICE: Wash off the brake fluid immediately if it comes into contact with a painted surface.
3. DISCONNECT FRONT FLEXIBLE HOSE
a. Remove the union bolt and a gasket from the disc brake cylinder, then disconnect the flexible hose from the disc brake cylinder.
4. REMOVE DISC BRAKE CYLINDER ASSY FR LH
a. Remove the 2 bolts and disc brake cylinder.
5. REMOVE DISC BRAKE PAD KIT FRONT (PAD ONLY)
a. Remove the 2 brake pads with anti-squeal shim.
Read more
1999-2000 Toyota Camry Radio Replacement
The plastic dash panel surrounding the radio and air conditioner controls must be unsnapped from the dash in order to gain access to the bolts which secure the radio. Pull out the ashtray at the bottom of the plastic dash panel. With your hands, grab the bottom of the plastic dash panel below the ashtray location and pull firmly until the plastic dash panel begins to unsnap from the dash. Continue to pull the dash until the sides and top of the dash panel completely unsnap from the main dash assembly. The radio is secured to the dash with four (4) 10 mm bolt screws, (1) at each side corner of the radio. Locate and remove all four bolt screws. Pull the radio out of the dash. Unplug the black cable plugged into the rear of the radio. Unplug (2) white plastic wire harness connectors snapped into the rear of the radio. The radio can now be completely removed from the dash.
Read more
Remote Starter Integration for the 2007 Toyota Camry equipped with the Smart Key System with Push Button Start
Preparation the Toyota Camry for installation
-Remove the driver’s side under dash, as well as the knee airbag bolts. Move the Airbag aside, but DO NOT DISCONNECT the Airbag connector in order to avoid setting any vehicle codes.
-Remove the driver’s side floor heating duct, in order to access the vehicle IMI & IMO wires easily.
The remote car starter will be installed in a conventional manner even if the car is equipped with the Smart Key “Push-to-Start” system.
Read more
2007 Toyota Camry/Camry HV Interface Kit For iPod
Vehicle Disassembly (a) Set parking brake. (b) Remove the negative battery cable. (Fig. 1-1) (1) Protect the fender before starting. (2) Do not touch the positive terminal with any tool when removing cable. (c) Remove instrument panel garnish LH: (1) Disengage the 2 clips and remove the instrument panel garnish. (Fig. 1-2) NOTE: Pull the instrument panel garnish up at a 45º angle to remove it. (d) Remove instrument panel garnish RH: (1) Disengage the 2 clips and remove the instrument panel garnish. (Fig. 1-3) (e) Remove floor shift position indicator for automatic transmission. (1) Unscrew shift knob. (2) Disengage the 6 claws and 3 clips and remove assembly. (Fig. 1-4) (3) Disconnect any connectors. (f) Read more
2005 Toyota Prius Pluses
Mid-size sedan with the outside dimensions of a Toyota Corolla and the inside dimensions of a Toyota Camry. 1.497 liters, 16-valve 4 cylinder engine: Power: 57 kW (76 hp) @ 5000 rpm; Torque: 111 N-m (82 lb-ft) @ 4200 rpm. Provides motive power and recharges the battery. (See bottom for more details.) Ni-MH (Nickel Metal Hydride) 201.6-Volts battery: 38 kW (51 hp). There is a normal 12- Volts battery, also. Hybrid System net power: 82 kW (110 hp). It weighs only 86 lb and has a life expectancy of 10-12 years or 150,000 to 200,000 miles (10,000 recharging cycles.) 500-Volts permanent-magnet electric motor/generator: Power: 50 KW (67 hp) @ 1200- 1540 rpm; Torque: 400 N-m (295 lb/ft) @ 0-1200 rpm. Provides motive power from the battery and recharges the battery using vehicle kinetic power when braking or coasting. (See bottom for more details.)
Read more
05 Toyota Camry SIRIUS Satellite Radio Operation Instructions
This section describes some of the basic features on Toyota audio systems. Some information may not pertain to your system. Your audio system works when the ignition key is in the “ACC” or “ON” position. TURNING THE SYSTEM ON AND OFF Push “PWR·VOL” to turn the audio system on and off. Push “AM”, “FM1”, “FM2”, “FM1·2”, “FM”, “SAT”*, “TAPE”, “CD” or “DISC” to turn on that function without pushing “PWR·VOL”. You can turn on each player by inserting a cassette tape or compact disc.
Read more
2004 Toyota Camry L4-2.4L Rear Strut Assembly
SHOCK ABSORBER LH REPLACEMENT
1. REMOVE REAR WHEEL
2. REMOVE REAR SEAT CUSHION ASSY
3. REMOVE REAR SIDE SEAT BACK ASSY RH
4. REMOVE REAR SIDE SEAT BACK ASSY LH HINT: Remove the LH side by the same procedures with the RH side.
5. REMOVE ROOF SIDE GARNISH INNER RH
6. REMOVE ROOF SIDE GARNISH INNER LH HINT: Remove the LH side by the same procedures with the RH side.
7. REMOVE CENTER STOP LAMP ASSY
8. REMOVE PACKAGE TRAY TRIM PANEL ASSY
9. REMOVE REAR SEAT 3 POINT TYPE BELT ASSY OUTER
10. SEPARATE REAR STABILIZER LINK ASSY LH
Read more
Exhaust System Installation For 2007 Toyota Camry LE/SE/XLE
Original Exhaust System Removal
Note: With a used vehicle, we suggest a penetrating spray lubricant to be applied liberally to all exhaust fasteners and allowing a significant period of time for the chemical to lubricate the threads before attempting to disassemble.
1. Unbolt the flanges shown in figure 1 located just in front of the muffler assemblies. Place the nuts to the side for use during the installation of your new exhaust.
2. Lubricate all the hangers and rubber isolators.
3. Using a muffler stand or an additional person to hold the right muffler assembly in place, remove the hangers from the rubber isolators and then remove muffler as shown in figure 2.
4. Repeat step 3 for the removal of the left side muffler assembly.
Read more
1992-96 Toyota Camry Pro.Fit Part Number TY-50-92 Installation Instructions
All instructions assume a drivers seat vantage point. Caution is advised when removing and reassembling wood or plastic parts of a dash. Applying unnecessary force or pressure may cause a piece to crack or break. Pro.Fit logo and part number will be right side up and readable when installed.
TOOLS REQUIRED: #2 Phillips screwdriver, hook tool.
PARTS INCLUDED: Pro.Fit VSMTM, instructions.
LOCATION: To the right of the radio.
Read more
