2008 Volkswagen Caddy Maxi Life
The Caddy Maxi Life. The new vehicle combines the qualities of a transporter with the versatility of a compact people carrier in a new class of vehicle. Compared to the familiar Caddy, the Maxi has been stretched from 4.41 metres to 4.88 metres. This has created an amazingly spacious vehicle with up to 4,200 litres of stowage volume (in the panel van version). Moreover, the multitalent is equipped with a new top-of-the-range engine: a TDI that generates 103 kW of output and 320 newton-metres of torque.
Read more
2006 Acura TL Power Steering Removal
This manual contains STEERING WHEEL REMOVAL for Acura TL.
SRS components are located in this area. Review the SRS component locations (see COMPONENT
LOCATION INDEX ) and the precautions and procedures (see PRECAUTIONS AND PROCEDURES )
before performing repairs or service.
1. Make sure you have the anti-theft codes for the radio and the navigation system, then write down the
customer’s audio presets.
2. Align the front wheels straight ahead, then remove the driver’s airbag from the steering wheel (see
DRIVER’S AIRBAG REPLACEMENT ).
Read more
2005 Ford Truck F 150 2WD Pickup Ignition System Spark Plug Removal Instructions
2005 Ford Truck F 150 2WD Pickup V8-5.4L SOHC VIN 5 Vehicle Level – Engine, Cooling and Exhaust Engine Technical Service Bulletins – All Technical Service – Bulletins – Ignition System, Spark Plug Removal Instructions.
Some 2004-2008 F-150, 2006-2008 Mark LT, 2005-2008 F-Super Duty, Expedition, and Navigator, with 5.4L 3-V engine; 2005-2008 Mustang, 2006-2008 Explorer, Mountaineer, and 2007-2008 Explorer Sport Trac with 4.6L 3-V engine; 2005-2008 F-Super Duty, 2006-2008 and F-Stripped Chassis, with 6.8L 3-V engine may experience difficulty with spark plug removal. This may cause damage to the spark plug and leave part of the spark plug in the cylinder head. Affected engine build dates are as follows: 5.4L 3-V and 6.8L 3-V before 10/9/07, 4.6L 3-V before 11/30/07.
Read more
2006-2008 Audi A3 Body Exterior Removal and Installation
Keep adhesive surface free of dirt and grease. Only cut back adhesive surface shortly before installation. Do not prime or use a cleaning solution on the adhesive surface. Make sure there is a slight overlap at adhesive joining points, otherwise there may be leaks in these areas.
Bonded panel must be inserted in the vehicle within a maximum of 10 minutes after start of application, otherwise the bonding properties of adhesive sealant material will be impaired. Observe minimum curing times for bonded panel Minimum curing times for bonded sunroof panel.
Read more
2006 Toyota Corolla Engine Control Module Removal and Installation
REPLACEMENT 1. DISCONNECT BATTERY NEGATIVE TERMINAL
2. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY
a. Remove the screw from the glove compartment door stoppers.
b. Deform the upper part of the glove compartment door assembly to release the stoppers.
c. Pull the glove compartment door assembly upward to remove it.
3. REMOVE ECM
a. Remove the 2 clips using a clip remover, then open the cover.
b. Disconnect the 4 ECM connectors.
Read more
1989 Nissan Pickup (200SX & 300ZX) Timing Belt Removal & Installation
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal (200SX & 300ZX) 1. Disconnect negative battery cable. Release fuel pressure from system. Raise and support vehicle. Remove right wheel and engine side cover (if necessary). Drain cooling system. Remove cooling fan duct. Remove engine coolant reservoir. Remove actuator and remove radiator hoses. Do not allow coolant to contact drive belts. 2. Remove front upper and lower belt covers. See Fig. 1 . Remove drive belts and set No. 1 cylinder at TDC of compression stroke. Remove idler bracket of compressor drive belt and crankshaft pulley. Remove timing belt by removing timing belt tensioner and return spring.
Read more
1987 Mercedes Benz 300TD (124 Chassis) Injection Pump Removal and Installation
Procedure for remove and install injection pump, vehicle: 1987 Mercedes Benz 300TD (124 Chassis) L6-2996cc 3.0L DSL SOHC Turbo 603
Vehicle Level – Powertrain Management – Fuel Delivery and Air Induction – Diesel MFI Pump – Service and Repair – Injection Pump Removal and Installation
PRELIMINARY PROCEDURES
Remove bottom section of noise encapsulation.
Remove belt tensioning device.
Remove fan cowl and fan.
Read more
1999 Ford Ranger Trucks Gasoline Engine Performance Removal
Removal & Installation (3.0L, 3.8L, 4.0L & 5.0L) 1. CMP sensor is located on top of engine, near intake manifold. See Fig. 3 Fig. 3: Locating Camshaft Position (CMP) Sensor (3.0L, 3.8L, 4.0L & 5.0L; 4.2L Similar) Courtesy of FORD MOTOR CO. 2. Disconnect negative battery cable. 3. Before removing, note position of electrical connector on CMP sensor. Disconnect CMP sensor electrical connector. NOTE: For Explorer models with 4.0L push rod engine, remove the upper intake manifold. See REMOVAL & INSTALLATION (4.0L VINX) under UPPER INTAKE MANIFOLD. 4. Remove CMP sensor screws and CMP sensor. To install, reverse removal procedure. Ensure CMP sensor electrical connector is pointing in original direction. Tighten CMP sensor to specification. See TORQUE SPECIFICATIONS . NOTE: If the synchronizer is turned while removing the CMP sensor, it must be re-aligned before CMP sensor is installed. See CMP.
Read more
1999 Subaru Forester S Timing Belt Removal and Installation
Removal 1. Disconnect negative battery cable. Raise and support vehicle. Remove engine under cover. 2. Lower vehicle. Remove radiator coolant reservoir, and set aside. Remove electric cooling fan and radiator shroud. 3. On Impreza and Forester, remove accessory drive belt cover. On all models, remove accessory drive belts. 4. Hold crankshaft pulley stationary, and remove crankshaft pulley center bolt. Remove crankshaft pulley. Remove timing belt covers. 5. Turn crankshaft to align crankshaft and camshaft timing notches with marks on rear timing cover and engine block. See Fig. 1 and Fig. 2 . On manual transmission models, remove timing belt guide from top of crankshaft pulley. 6. On all models, if reusing old belt, use White paint to mark timing belt in relation to sprocket timing marks. See Fig. 3. Also mark timing belt direction of travel. On 2000 and newer vehicles, count number of teeth between marks. For correct count, see INSTALLATION MARK MEASUREMENT SPECIFICATIONS table. 7. Remove No. 2 timing belt idler pulley. See Fig. 4. Remove timing belt. Remove timing belt automatic tensioner with rod facing up.
Read more
2006 Cadillac BLS
A design team led by GM Designer Chip Thole designed the new Cadillac BLS show car and the premium sedan is thus immediately recognizable as a member of the Cadillac family. “The most striking feature is the emphasis of the vertical lines on the front and rear,” says Thole. “The characteristic v-form of the chrome-plated grill is picked up again by the trunk lid. The large side faces communicate a sense of strength and solidity.” Nineteen-inch multi-spoke alloy wheels underline the impressive looks of the show car.
Read more
