2004-05 Chevy Colorado Prerunner Rear Bumper Installation
This kit should only be installed on a vehicle that is in good mechanical condition. Before installing the kit, replace worn or corroded parts. If the vehicle is suspected to have been in a collision or abused, DO NOT install the kit. The components in this kit do not eliminate weaknesses that may exist in the original equipment components.
Read more
HP10005 Air Suspension Kit for GMC/Chevrolet 2500 HD/3500 2WD/4WD
This kit includes “push to connect” airline fittings. They require the end of the airline to be round, square and cleanly cut to ensure the internal seal will not leak. The airline must only be cut with a sharp razor knife or hose cutter.
PREASSEMBLY OF THE AIR SPRINGS THE UPPER PLATE
1. Place the upper roll plate (with the rounded side towards the air spring) on the top of the air spring (top being the end with the air port). Repeat on the other air spring.
2. Install the air fittings supplied into the inlet ports of the air springs, use thread sealant to prevent air leaks. The air spring ports will be installed towards the center of the vehicle. The passengers side fitting will point towards the front of the vehicle. Do not over tighten the fittings.
THE UPPER BRACKET
3. Place the drivers side upper mounting bracket on top of air spring aligning the two mounting holes as shown in the photo.
Note: The driver side bracket mounts to the air spring through the elongated holes on each side of the air inlet port cutout. The passenger side bracket mounts to the air spring through the elongated holes opposite the air inlet port cutout.
THE LOWER BRACKET
4 Install the clinch stud into the drivers side lower bracket hole, shown in the photo. This is an interference fit into the bracket. Clinch stud not required on the passengers side lower bracket. 2500 model only (3/4 ton trucks) require a 3/8″ bolt and nut to be installed in both lower brackets as shown. The bolt head is installed opposite the air spring. The nut will fit inside the roll plate cavity. Tighten the nut securely.
Complementing the 987C Boxster S with the 987A Cayman S Front and Rear Bumper Covers
Why change the Boxster S Bumpers? You fall in love with a Porsche—and start improving, modifying, and changing it until it reflects who you are. It doesn’t matter what kind of perfection you’re chasing. Porsche geekdom is one religion with many denominations: club racing, driver’s education, autocrossing, rallying, touring, preservations, concours, and socialization. If you don’t change it and make it uniquely yours, then you’re not really a Porsche guy, just a temporary owner.
Read more
2003-09 Dodge Ram 2500/3500 II Mount Kit Installation Instructions
For easier assembly and installation, vehicle and all snowplow components should be on a smooth, level, hard surface, such as concrete.
1. Remove license plate bracket and retain for vehicle owner. Remove bumper from bumper brackets. Retain fasteners.
2. Remove bumper brackets from frame. Diesel and V10 applications: On these applications, you must first remove the top two intercooler fasteners. Then push intercooler up and out to provide clearance to remove bumper bracket bolt assembly. Retain fasteners. Vehicles equipped with tow hooks will need tow hooks and tow hook brackets removed. These cannot be reinstalled with plow mount. Retain tow hooks, brackets and fasteners for reinstallation if snowplow is removed.
Read more
2001-2004 Audi A6 4B C5 Single-Frame front bumper HF 7551 Installation Guide
1. Removal of the original bumper:
Remove all screws which hold the bumper. Also remove the screws which hold the alloy bar and remove the bumper with the alloy bar. Remove the alloy bar from the bumper and install it into the new Hofele-Design bumper.
2. Placement of the Hofele-Design front bumper on the car:
Place the new bumper on the car but do not yet bolt it on.
3. Preparation of the bonnet:
Remove the front grill and the rubber strap behind it. Install the front grill (HF 7052-S4 / RS4) in the extension piece.
Read more
350Z GT Aero Front Bumper Installation Manual
This product is meant to fit Nissan 350Z only. Please check the parts before mounting.
- Mounting Procedure
Please follow the manufacturer’s repair manual for proper front bumper cover removal procedure.
（Remove the side bracket from the OEM bumper. ）
(Remove the impact foam from the front of the bumper.）
Install the side bracket onto the GT bumper by reversing the steps used to remove it.
Install the GT bumper using the factory clips and screws to the original locations.
Read more
2008 Chevrolet Aveo Euro
The most significant features of this completely reworked model are its striking exterior, its high-class interior and a new, even more efficient petrol engine. Like its notchback stable mate, the new hatchback model will now bear the Aveo name throughout Europe.
The Aveo hatchback sports Chevrolet’s new design features, as characterised by the big horizontally split radiator grille with a body-coloured crossbeam and the brand logo sitting prominently in the center. The dynamic detailing includes large, curved, clear-glass headlamps and fog lamps that project like spotlights from the lower part of the bumper. In profile, the body’s prominent shoulder lines catch the eye, while the back of the car is dominated by the solid bumper and the round tail lamps in a clear-glass housing.
There is a choice of two petrol engines: a new 1.2-litre unit with an output of 84 hp , and the existing 1.4-litre engine, which now develops 98 hp and is available with automatic transmission.
2008 Chevrolet Aveo
The Aveo hatchback sports Chevrolet’s new design features, as characterised by the big horizontally split radiator grille with a body-coloured crossbeam and the brand logo sitting prominently in the center. The dynamic detailing includes large, curved clear-glass headlamps and fog lamps that project like spotlights from the lower part of the bumper. The bonnet follows the lines of the radiator grille. Eye-catching contours, which flow from the bonnet to the A-pillar, highlight the sporty look.
Read more
2008 Three door Chevrolet Aveo
Chevrolet hostesses wear outfit that won first prize in Fashion in “Young? Creative? Chevrolet!” art contest Zurich/Geneva. The highlight of this year’s Chevrolet Europe presentation at the Geneva Motor Show is the new three-door Chevrolet Aveo, which will be shown to the public for the very first time.
Read more
2008 Chevrolet Aveo Penny Edition
Credit-crunched Londoners grabbed pocketfuls of pennies today at the launch of a 20-foot billboard advert made entirely from one-pence coins. The unique installation – made using over 20,000 pennies – only lasted 30 minutes as hundreds of opportunistic passers-by seized their moment to pick up a penny or two.
The penny billboard was unveiled in London’s New Oxford Street to advertise the 769,500-pence starting price of the new Chevrolet Aveo.
Read more
