Revised Steering Wheel Position Sensor or Steering Shaft Lower Bearing
This bulletin is being issued to revise the Steering Wheel Position Sensor or Steering Shaft Lower Bearing Replacement procedure in the Variable Effort Steering (1998-2001 model years) or Steering Wheel and Column (2002-2003 model years) and add the Steering Wheel Position Sensor Centering procedure in the Steering Wheel and Column sub-sections of the Service Manual. Please replace the current information in the Service Manual with the following information.
Read more
Red Snub Mount Installation
1. Allow engine to cool before beginning installation.
2. Access the underside of the vehicle.
- APR recommends utilizing a lift for this installation.
- A jack with jack stands or ramps can be used if a lift is not available.
3. Remove the Splash Shield. With the flat head screw driver, unfasten all of the quarter turn screws. Note how splash shield is oriented in the car before removing.
4. Remove the three 6mm bolts from the front lower engine mount.
Read more
2001 Chevrolet Impala V6-3.8L Oil Pan Replacement
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the fuel injector sight shield.
3. Disconnect the intake air temperature (IAT) sensor electrical connector.
4. Remove the air inlet duct from the throttle body.
5. Remove the drive belt.
Read more
2007 Audi Metroproject Quattro Concept
The Audi Metroproject Quattro, has a battery pack in visibly mounted in the boot, and lit in tranquil blue lights with a charge indicator on the side.
The supermini Audi A1 should be available with a turbocharged gas engine, turbocharged diesel engine, ranging in size from 1.2 litres to 2.0 litres. A base model with an 80 horsepower, naturally aspirated 1.4 litre engine is also expected to hit showroom floors.
Read more
Audi A4 Avant CM 11195 Installation
Installation Steps:
1. Removing fasteners from the exhaust brackets to lower exhaust, support as needed to prevent damage.
2. Raise hitch into position. Using a center punch, punch through the center hole of the hitch and into the heat shield.
3. Lower hitch and cut out the area of the heat shield covering the access hole. See heat shield trim detail.
4. Fishwire 1/2-13 X 1 1/2″ carriage bolt and SP6 spacer through the access hole and out the forward most hole in frame, both sides. (SEE FISHWIRE TECHNIQUES)
Read more
2008 Audi R10 TDI Le Mans
The Audi R10 TDI remains unbeaten in the Le Mans 24 Hour race: in its third attempt, the diesel sportscar won the French endurance classic yet again. After the incredible thrill of the 76th edition of the race, Dindo Capello (Italy), Tom Kristensen (Denmark) and Allan McNish (Scotland) triumphed at the wheel of the Audi R10 TDI number 2.
Read more
2007 Audi Q7 4.2 Quattro Premium
With a host of innovative extras included as standard equipment – including Rear View Camera with Acoustic Parking – the Audi Q7 4.2 Premium model delivers superb power, efficiency, and control via a 350 hp 4.2 V8 equipped with FSI® Direct Injection technology, and combined with quattro® all-wheel drive and a 6-speed Tiptronic® transmission. More pictures below…
Read more
2008 Audi RS6 Avant
The Audi RS models from quattro GmbH are the ultimate in sportiness, complemented by powerful and elegant design, exclusive equipment and perfect quality. It has also meanwhile become a good tradition that their sports performance is combined with the high utility value of an Avant: the very first Audi RS2, which appeared in 1993, was only built as an Avant model. Although the unique Audi RS driving sensation can now be experienced in saloon, Avant and Cabriolet models – as is the case with the current RS 4 – customers especially appreciate the combination of dynamism and versatility that an Avant offers.
Read more
2005-2008 Ford Mustang Edelbrock Lower Trailing Arms Installation
REMOVAL OF STOCK TRAILING ARMS
1. Place vehicle on level surface and place tire chocks in front of and behind front tires.
2. Support rear of the vehicle on the jackstands and remove the rear wheels.
3. Place a floorjack under the differential and lift up slightly to remove tension from the trailing arm bolts. Make sure not to lift the vehicle off the jackstands.
Read more
2011 Audi Q3 By Seat in Spain
Having agreed that the Q3 will be manufactured in Spain, a decision about production in the USA has been postponed. Mr. Stadler: “We will systematically explore our options in the context of the current market crisis. Audi is in a good position. There is currently no urgent need to select additional sites.”
Read more
