U-Cut-To-Fit GM & Chrysler Speedometer Cable Kit Installation Instructions
U-Cut-To-Fit Speedometer Cable Kit Installation
Step 1: Install outer housing to speedometer and route housing to transmission, making sure to keep away from exhaust pipes.
Step 2: Hold housing up to transmission to determine length and mark a cut line. Remove housing from vehicle and cut housing at the cut line.
Step 3: After cutting housing, install end of housing into GM or Chrysler trans end fitting. Figure 1 Slide housing nut up and tighten until housing is locked into fitting.
Note: Do Not over tighten nut as it will result in fitting failure.
Read more
ENIGMA Cable Descriptions User Manual
Specifications written in this document are believed to be accurate, but are not guaranteed to be entirely free of error. The information in this manual is subject to change for functional or performance improvements without notice. Please make sure your manual is the latest edition. While the information herein is assumed to be accurate, SYS MICRO (the manufacturer) assumes no responsibility for any errors or omissions. The manufacturer makes and you receive no warranties or conditions, express, implied, statutory or in any communication with you. The manufacturer specifically disclaims any implied warranty of merchantability or fitness for a particular purpose.
Read more
Front Connected 63 Fuse Fitting
Method of Cabling Front connected fuse fittings
1. Remove red nylon insulating shroud to release cable sleeve.
2. Remove cable sleeve.
3. Fit cable sleeve over cable.
4. Fit conductor into fuse base terminal and tighten cable clamping screw to secure. If flexible cables are used, their relatively fine strands may be given increased protection by the use of thin wall copper ferrules over the conductor.
The following should be taken into account:
Read more
2004 Honda Truck CR-V Alternator Replacement
The alternator replacement removal and installation for 2004 Honda Truck CR-V. 1. Disconnect the battery negative cable, then disconnect the positive cable. 2. Remove the bolt (A) securing the battery clamp, then remove the bulkhead cover (B). 3. Remove the upper brackets and cushions. 4. Remove the drive belt. 5. Remove the auto-tensioner. 6. Remove the three bolts securing the alternator. 7. Disconnect the Read more
VW/Audi PhatBox Digital Media Player Quick Start Guide
Section I : Installing the PhatBox
Mounting the PhatBox
When choosing a mounting location remember: Leave at least 3 inches of clearance for the cable. The PhatBox should be mounted parallel or perpendicular to the floor of the car. Don’t mount near wiring or fuel lines. Leave the front of the PhatBox unobstructed for easy insertion of and removal of the cartridge. The unit should be mounted to a hard stable surface, such as particle board or sheet metal.
Read more
Jeep/Dodge Perm-Lok 1100 Installation Instructions
These instructions have been designed for unaltered vehicles. Before you start, check for any variations. Each vehicle may dictate it’s own control mount and cable routing. Therefore, you will need to study the pictures and use your good judgement or seek professional help. Lift kits may govern how and where the cable is routed. Always keep the cable away from heat (exhaust) and rough or sharp edges. If you are concerned about lower cable damage or abrasion, we recom- mend cutting a length (about 3 feet) of 5/8” ID plastic or rubber hose (garden or heater) to be slid over the cable before assembly.
Read more
2007 Toyota Camry Hybrid Sirius XM Radio Satellite Installation
Cable Routing and Installation (a) Install and route the tuner cable from the center cluster and along the front support bar. (Fig. 3-1) (b) Provide sufficient cable slack to connect to the tuner, and then secure the cable to the existing wire harness with lock tie. Cut excess off lock tie. Connect wire harness to head unit. (c) Using lock ties attach to existing W /H. Trim lock tie excess. (Fig. 3-2) (d) Route to the existing clamps. (Fig. 3-2) (f) Route the cable as shown and secure with lock tie. Trim lock tie excess. (Fig. 3-4) (g) Route the tuner cable under the rear passenger seat and secure with cushion tape. (Fig. 3-5) NOTE:Clean the area for the cushion tape with the approved cleaner.
Read more
ABTI-GM1 General Motors Class II Bluetooth Interface Installation Manual
The ABTI-GM1 is designed to allow full integration of Motorola’s IHF-1000 Bluetooth HandsFree kit (Sold separately) with GM Class 2 vehicles listed inside. The kit will allow users to listen to phone calls through their car stereo. The currently playing radio source will be automatically muted, and the phone volume may be controlled by the radio. OnStar operation is unaffected.
Read more
DICE ipod BMW Z4 Installation
This “how to” guide installs the kit into a Z4 with no CD changer and a standard business cd (no sat nav), ipod location in the central compartment.
1: The kit
2: Disconnect battery with 10mm socket
3: Now it’s a bit of a pain, but to get easier access to centre console I removed the boot carpet. Use a large flat head screwdriver to remove the retaining screws on the left and the right hand side of the boot. You need to reach behind the carpet to hold the nut at the back.
Read more
2003-07 Dodge Dakota 4.7L PowerAid Throttle Body Spacer
Your PowerAid Throttle Body Spacer was carefully inspected and packaged. Check that no parts are missing, or were damaged during shipping. If any parts are missing, please contact AIRAID.
Installation Instructions. Read Me!
1. DISCONNECT NEGATIVE (-) BATTERY CABLE.
2. Remove air intake hose assembly.
3. Remove throttle body air intake box and save bolts.
4. Remove (3) bolts from the throttle body.
Read more
