2001 Lexus GS 300 L6-3.0L (2JZ-GE) – Blower Motor Assembly
REMOVAL
1. REMOVE No.2 UNDER COVER
2. REMOVE BLOWER MOTOR
a. Disconnect the connector.
b. Remove the 3 screws and blower motor.
Read more
2010 BMW M6 Limited Edition
Bmw revealed today the M6 Competition Limited Edition, a new car which will be present at this year’s Frankfurt Motor Show among other premieres such as the new X1 SUV, X6 Hybrid, ActiveHybrid 7 and the Vision EfficientDynamics Concept. Limited to 100 units, the new M6 Competition Limited Edition features a special Frozen Gray Matt finish, new full-leather two-tone interior, new floor mats and sill plates with the “M6 Competition” logo.
Read more
2008 Ford Truck Escape 2WD V6-3.0L Blower Motor Resistor Service and Repair
2008 Ford Truck Escape 2WD V6-3.0L Vehicle Level Heating and Air Conditioning Blower Motor Resistor Service and Repair
Removal and Installation
1. Lower the glove compartment.
2. Disconnect the blower motor resistor electrical connector.
3. Remove the 2 blower motor resistor screws.
Read more
1995 Buick Regal V6-231 3.8L VIN L SFI – HVAC Blower Motor
HVAC Blower Motor Noise/Vibration
(Install New Blower Motor Assembly and/or VP Lower Compartment Access Hole Cover)
Models:
1995-96 Buick Regal
1995-96 Oldsmobile Cutlass Supreme
1994-96 Pontiac Grand Prix
Condition
Some owners may comment on noise and/or vibration from the HVAC blower motor.
This noise/vibration may be due to the blower motor being out of balance, or contents
(i.e. tissues, papers, etc.) in the instrument panel (I/P) lower compartment being drawn
into the blower motor assembly through the re-circulation door during MAX A/C mode.
Read more
2001 GMC Truck C 1500 Truck 2WD Front Side Door Window Regulator Motor Replacement
Removal Procedure
1. Raise the window. If the window motor is inoperable, remove the window to gain access to the window motor retaining screws. Refer to Front Side Door Window Replacement.
2. Remove the power window module.
3. With the window regulator on the bench, remove fasteners one (1) and two (2) which will disconnect the drive housing and motor (4) from the rail (5) motor slides out of the gear/spool, hold the gear/spool into the housing with your fingers. The spool will unwind if it comes out of the housing.
4. Holding the motor and housing together, remove fastener three (3).
5. Slide the motor partially out of the gear/spool allowing finger access to the gear spool (6). Hold the gear/spool into the housing and remove the motor (7).
Read more
2010 Peugeot RCZ Limited Edition Car
The Limited Edition RCZ comes very well equipped with equipment such as the WIP COM 3D (and the Peugeot Emergency service), the Vision Pack (directional bi-Xenon headlamps, headlamp wash, etc.), the Nappa Leather Pack (heated electric leather seats, over-mats, etc.), the Easy Motion Pack (front and rear parking assistance, etc.), the alarm, etc.
Read more
Peugeot 308 RC Z Arrives in Second Life
The new 308 RC Z concept car presented at the Frankfurt Motor Show will be on trial on the Peugeot Island which will be opened in the Second Life 3D virtual world on 11 September. The magic of this interactive, multidimensional graphic world allows Second Life avatars* to climb on board this new spearhead of the Peugeot Brand andlive a unique experience by taking a journey over a race track in this innovative virtual place of stylistic composition.
Read more
1994–1999 Cadillac DeVille Blower Motor Installation Instructions
On 1994 and 1995 models: NOTE the below removal procedures pertain to the OE blower motor that was a two piece set up. Remove the cross tower or cross member brace. Disconnect solenoid purge valve electrical and vacuum connectors. Position components aside for access. Remove solenoid purge valve. Remove 3 center screws and inertia plate from blower motor. Reinstall two screws to prevent motor and housing from separating. Disconnect wiring connector from blower motor. Remove 5 blower mounting screws.
Read more
1994-1997 Cadillac Seville Revised HVAC Blower Motor Installation Procedures
The intent of this bulletin is to provide technicians information regarding the proper installation of the Heating, Ventilation and Air Conditioning (HVAC) Module blower motor (with impeller) assembly.
The current available HVAC Module blower motor for the above listed vehicles can be identified by the three mounting holes (1). The original equipment blower motor had five mounting holes.
In order to avoid confusion and ensure a high level of customer satisfaction, when replacing an HVAC Module blower motor, refer to this bulletin for the appropriate procedure.
Read more
Rebuilding a Series Starter Motor
Before you begin on your quest of rebuilding your starter motor, the first thing you should do is check all your grounds, and leads. These should be clean and well connected. A good way to have your grounds wired is a large cable from the battery’s negative post to the frame, and another large cable from the frame to a starter mounting bolt. The positive lead goes from the battery to the starter button, then from the starter button to the positive terminal on the end of the starter motor.
Read more
