Audi TT 1.8t A.W.E. Tuning DV1 Diverter Valve Installation Instructions
With the DV1 Diverter Valve, we believe you have purchased the finest diverter valve for the money. Follow these instructions, and you’ll have your new A.W.E. Tuning DV1 Diverter Valve installed quickly and easily.
Step 1: Here’s an overview picture of the transverse 1.8T engine found in the Audi TT, VW Golf/Jetta/New Beetle 1.8T. The 225hp TT engine looks a little different, but the install of the A.W.E. Tuning valve is the same procedure. For picture clarity, and ease of install, the decorative engine cover has been removed. Removing the cover is easily done by twisting the “+” shaped fasteners on the cover 90 degrees. They’ll pop up when free, allowing you to grab the cover and lift it up and out of the engine bay. (New Beetle requires removing 2 10mm nuts hidden under trim caps, and then sliding forward and out) We’ve also removed the PCV damper in the following pictures for clarity. You won’t need to remove this item to install the valve.
Read more
00-05 Audi 2.7T Engines A.W.E. Tuning DV1 Diverter Valves Installation Instructions
Removal of stock valves:
Removal of the stock diverter valves requires removal of decorative engine cover with the “V6 BITURBO” badging. Lift off the cover after twisting X-shaped plastic fasteners 90 degrees with a flat blade screw driver. Valve replacement is much easier done on a cool engine.
Read more
Stratmosphere HyperBoost Valve (Audi S4) Installation Instructions
Step 1- Remove motor cover
This is the small triangular cover in the front of the engine where the dipstick is located (figure 1). Just twist the two screws 90 degrees counterclockwise. Then lift up the cover. The cover fits onto a rubber round mount at the point on the “triangle” as well. It’s just pressed on there.
Read more
2005 Ford Taurus Engine Controls Vacuum Leakage Noise Possible DTC’s
Some 2005 Taurus and Sable vehicles equipped with a 3.0L 2V and some 2003-
2005 Lincoln LS vehicles equipped with a 3.0L 4V engine may exhibit a vacuum
leakage noise or lean codes and/or malfunction indicator lamp (MIL) on. The
cause may be a leak at the 0-ring on the intake manifold tuning (IMT) valve.
ACTION
Follow the Service Procedure steps to correct the condition.
Read more
Long Tube Header Installation For Chevrolet Camaro 6.2L V8 PN 17249
This Borla Performance Stainless Steel Long Tube Header System (Part Number 17249) has been designed for the Chevrolet Camaro equipped with a 6.2L V-8 engine with an automatic or manual transmission.
Original Manifold System Removal
Read more
Nissan Vent Control Valve Replacement Service Bulletin
All Nissan models using Vent Control Valve P/Ns 14935-AM60A / AM60B
SERVICE INFORMATION
When replacing the EVAP canister vent control valve for any reason: Use the one listed in the PARTS INFORMATION section of this bulletin on Page 2. For vent control valve replacement procedure, refer to the appropriate section of the Electronic Service Manual (ESM) if needed. Read more
1996-Up Nissan Evap Vent Control Valve Diagnostics Service Bulletin
If an applied vehicle has one (or more) of the following DTCs stored in Self Diagnosis, use the Service Procedure below to check the operation of the EVAP vent control valve.
IMPORTANT NOTES:
• If DTC(s) other than the ones listed below are found stored in Self Diagnosis, the EVAP vent control valve is NOT the cause of the incident.
• If the EVAP vent control valve passes the tests outlined in the following Service Procedure, the cause of the incident is NOT the EVAP vent control valve.
Read more
2003 Ford Taurus V6-3.0L Upper Intake Manifold Removal and Installation
Upper Intake Manifold Removal 1. Remove the air cleaner outlet tube. 1 Remove the hoses. 2 Loosen the clamps. 3 Remove the air cleaner outlet tube. 2. Remove the pin-type retainers and the accelerator cable splash shield. 3. Disconnect the throttle cable and the cruise control cable. 4. Disconnect the Throttle Position Sensor (TPS) and Idle Air Control (IAC) valve electrical connectors. 5. Disconnect the harness from the throttle body stud. 6. Disconnect the Exhaust Gas Recirculation (EGR) vacuum regulator and vacuum supply hoses. 7. Disconnect the Positive Crankcase Ventilation (PCV) and Evaporative Emissions (EVAP) vacuum hoses. 8. Remove the EGR valve. 1 Disconnect the vacuum hose. 2 Remove the nuts. 3 Remove the bolts. 4 Remove the EGR valve. 9. Remove the EGR Vacuum Regulator (EVR) valve. 1 Disconnect the vacuum hose. 2 Disconnect the electrical connector. 3 Remove the bolts. 4 Remove the valve. 10. Remove the eight bolts and the upper intake manifold. Remove and discard the gaskets. Clean all mating surfaces.
Installation
1. Position new gaskets in the upper intake manifold. 2. Position the upper intake manifold and install the bolts in the sequence shown. 3. Install the EGR vacuum regulator valve. 1 Position the valve. 2 Install the bolts. 3 Connect the electrical connector. 4 Connect the vacuum hose.
2005 Nissan-Datsun Sentra L4-1.8L Evap Canister Purge Volume Control Solenoid Valve
With CONSULT-II
Check air passage continuity of EVAP canister purge volume control solenoid valve
under the given conditions.
Without CONSULT-II
Check air passage continuity of EVAP canister purge volume control solenoid valve
under the given conditions.
Read more
2002 Ford Taurus Upper Intake Manifold Service and Repair
Removal 1. Disconnect the battery ground cable. 2. Remove the air cleaner assembly and the air cleaner outlet tube. 3. Remove the pin-type retainers and the snow shield. 4. Disconnect the accelerator cable, speed control actuator cable and the throttle return spring from the throttle body. 5. Remove the bolts, then position the accelerator cable bracket aside. 6. Disconnect the hoses. – Disconnect the vacuum hose. – Disconnect the evaporative emissions return tube. 7. Disconnect the electrical connectors. – Disconnect the Idle Air Control (IAC). – Disconnect the Throttle Position (TP) sensor. 8. Disconnect the engine wiring harness from the intake manifold support bracket. 9. Remove the upper intake Read more
