Audi A4/B7 RHD Electrical System for Towing Hitch
Read the installation manual prior to starting work.
The electrical kit should only be installed by qualified personnel.
Follow guidance in the current repair manual when carrying out installation work on the vehicle.
Caution – Disconnect the battery!
Danger of damage to the vehicle’s electronic system. Data which are stored electronically may get lost.
Read out the fault storage prior to starting work.
Note
During installation special attention has to be paid to the following points:
• Cables must not be pinched or damaged.
• All sealing elements have to be installed properly.
• The socket gasket has to be positioned on the insulating sleeve and not on the individual wires.
• Lay the cables such that they do not rub on the vehicle and are not bent.
• Do not lay any cables near the exhaust system.
Read more
2004 Audi A3 Direct Petrol Injection and Ignition System
Mixture preparation – injection Servicing injection system General notes on self-diagnosis
♦ The engine control unit has a self-diagnosis capability. Before carrying out repairs and fault finding the fault memory must be interrogated. The vacuum hoses and connections must also be checked (unmetered air).
♦ Fuel hoses in engine compartment must only be secured with spring-type clips. Clamping-type or screw-type clips must not be used.
♦ A voltage of at least 11.5 V is required for proper operation of the electrical components.
Read more
Fault Code Manual for Mercedes-Benz
This book is designed to help you in the basic diagnostic procedures for Mercedes Benz.
It is intended to be a starting point in the diagnostic process and is not intended to be a complete
resource.
THE DIAGNOSTIC PROCESS
The diagnostic process divides itself into several levels; Information Gathering, Analysis of Codes, Testing and then
Repair. W e will cover Information Gathering and Analysis of codes in this book.
For those experienced in diagnostics jump to page
Read more
2003-2004 Audi A4 Cabriolet Radio Communication
Radio system General information CAUTION! Before beginning repairs on the electrical system: Obtain anti-theft radio security code if necessary. Switch the ignition off. Disconnect battery Ground (GND) strap. On vehicles equipped with Audi Telematics by OnStar , switch-off the emergency (back- up) battery for the Telematic/Telephone Control Module prior to disconnecting vehicle battery. Use VAS 5051 Vehicle Diagnostic, Testing and Information System in mode “Guided Fault Finding” After reconnecting vehicle battery, re-code anti-theft radio if necessary and check operation. Also check operation of clock and power windows according to Repair Manual and/or Owner’s Manual. After Read more
Audi V1 Interface and V1 Power Hardwire Installation Guide
Installation with V1 hardwire
Requirements:
Audi vehicle with CAN bus or CDE interface for instrument cluster radio information.
Steering wheel buttons, TAPE button or additional wired button.
V1 Radar Detector
V1 Direct Power Adapter
2 straight 4 conductor RJ11 cables (like the ones included with the V1)
A-B USB cable for updating and setup
Read more
Kia Automotive Electrical
MODULAR FORMAT As a Kia service professional, you understand the importance of staying current with today’s complex automotive technology. The amount of training that a technician needs depends on factors like technical background, product knowledge and practical experience. To meet your needs, we have developed a modular training system to help you focus your efforts in the areas that are of the most value to you.
Read more
Audi Climate Control LCD Rebuild Kit
Please read and become familiar with these instructions before performing the actual repair. The LCD panel is fragile and can be damaged if incorrectly installed. Installation is very simple and straightforward. Many color photos are included to ensure a trouble free installation. Place several paper towels on your work surface so as not to scratch the buttons on your climate control panel.
1) Remove controller from the center console
Gently pry wood trim fascia panel (A) from center console using a flat edge tool. A flathead screwdriver with an overlay of electrical tape will prevent any marring of surfaces. Remove the two Phillips head screws on left and right sides (B). Climate control center will slide out. Remove all four electrical connectors by simply pushing the tab in with your thumb and pulling the connector away from its socket. All four connectors are mechanically different to prevent mismatch upon assembly.
2) Taking your controller apart
Remove the three Phillips head screws from holding the front control panel to the controller housing. In this photo two screws can be seen at the top. The 3rd is on the bottom side. If you do not have the four turquoise lamp holders as seen in this photo, your controller is LED backlit. Rebuild is the same, but you will not need the lamps provided in this kit. If your controller is an early version with a white enclosure, please go to the appendix for updated information. Gently pull the front panel away from the housing to expose the LCD controller board and its ribbon connector.
Restores cracked, leaking or missing segment LCD’s for the following vehicles:
• 1997-98 Audi A4 with electronic climate control center
• 1995-97 Audi A6 with electronic climate control center
• 1997-98 Audi A8 with electronic climate control center
• 1993-95 Audi 90 with electronic climate control center
• 1992 Audi 100 with electronic climate control center
• 1995-97 Audi S6 with electronic climate control center
• 1994-98 Cabriolet with electronic climate control center
2003 Toyota Tacoma G Electrical Wiring Routing
A 5 A/C Magnetic Clutch E 2 Electronically Controlled Transmission Solenoid A 7 A/T Oil Temp. Sensor E 3 Engine Coolant Temp. Sensor A 22 ABS Actuator with ECU A 23 Air Fuel Ratio Sensor (Bank 1 Sensor 1) F 1 Front ABS Speed Sensor LH A 24 ADD Actuator F 2 Front ABS Speed Sensor RH A 29 Accel Position Sensor F 3 Front Turn Signal Light LH F 4 Front Turn Signal Light RH B 1 Back–Up Light SW F 9 Front Airbag Sensor LH B 2 Brake Fluid Level Warning SW F 10 Front Airbag Sensor RH F 11 Fuse Box C 1 Camshaft Position Sensor C 2 Crankshaft Position Sensor G 1 Generator C 3 Cruise Control Actuator G 2 Generator D 3 Detection SW (Transfer L4 Position) H 1 Headlight LH D 4 Detection SW (Transfer Neutral Position) H 2 Headlight RH D 5 Detection SW (Transfer 4WD Position) H 5 Horn (High) H10 Horn (Low)
Read more
2003 Toyota Tacoma M Overall Electrical Wiring Diagram
[A] : System Title [B] : Indicates the wiring color. Wire colors are indicated by an alphabetical code. B = Black W = White BR = Brown L = Blue V = Violet SB = Sky Blue R = Red O = Orange LG = Light Green P = Pink Y = Yellow GR = Gray G = Green The first letter indicates the basic wire color and the second letter indicates the color of the stripe. Example: L–Y [C] : The position of the parts is the same as shown in the wiring diagram and wire routing. [D] : Indicates the pin number of the connector. The numbering system is different for female and male connectors. Example : Numbered in order Numbered in order from upper left to from upper right to lower right lower left The numbering system Read more
2007 Audi Metroproject Quattro Concept
The Audi Metroproject Quattro, has a battery pack in visibly mounted in the boot, and lit in tranquil blue lights with a charge indicator on the side.
The supermini Audi A1 should be available with a turbocharged gas engine, turbocharged diesel engine, ranging in size from 1.2 litres to 2.0 litres. A base model with an 80 horsepower, naturally aspirated 1.4 litre engine is also expected to hit showroom floors.
Read more
