Chrysler 300C/SRT-8 Headlight Disassembly
1) Remove the high beam bulb and turn signal bulbs, this allows the inside of the lamp to heat at the same rate as the outside of the lamp.
-First, test fit the headlight in the cool oven. The lamp should be situated in the center of the oven, away from the heating element. You can use a cookie sheet to shield the light from direct heat.
-Preheat the oven to 235 degrees, once pre-heated insert the lamp and set a timer for 20 Minutes.
Read more
2001 Lexus GS 300 L6-3.0L (2JZ-GE) – Blower Motor Assembly
REMOVAL
1. REMOVE No.2 UNDER COVER
2. REMOVE BLOWER MOTOR
a. Disconnect the connector.
b. Remove the 3 screws and blower motor.
Read more
1999.5-2001 Audi A4 (B5) HID conversion installation instructions
1. Take the kit out of the box and lay everything out. You can install either the ballasts or bulbs first but typically it is easier to install the bulbs first.
2. There are 3 T27 torx screws holding the headlight on. The 2 on top are visible in this picture.
3. with the 2 screws removed.
4. The third screw is shown here. A long extension is needed to get to it and an extendable magnet is helpful to retrieve the screw (or bit if it falls).
5. Disconnect the headlight and turn signal connectors and remove the headlight by pulling it toward the outside of the car and toward you.
Read more
2000-2001 Audi TT 1.8L Turbo Short Throw Shifter Installation Instructions
This B&M Short Throw Shifter has been designed to work on most 2000-2001 Audi TT 1.8L Turbo models. It has been engineered to greatly reduce shift throw and improve shifter feel. The B&M Short Throw Shifter has been designed to work with the stock knob as well as the B&M Knob. Check the parts and tools lists at the beginning of these instructions for the supplied parts and the tools required to install your B&M Short Throw Shifter. Installation of the B&M Short Throw Shifter can be accomplished by anyone with minimal mechanical experience.
Read more
2001-2004 Audi A6 4B C5 Single-Frame front bumper HF 7551 Installation Guide
1. Removal of the original bumper:
Remove all screws which hold the bumper. Also remove the screws which hold the alloy bar and remove the bumper with the alloy bar. Remove the alloy bar from the bumper and install it into the new Hofele-Design bumper.
2. Placement of the Hofele-Design front bumper on the car:
Place the new bumper on the car but do not yet bolt it on.
3. Preparation of the bonnet:
Remove the front grill and the rubber strap behind it. Install the front grill (HF 7052-S4 / RS4) in the extension piece.
Read more
2008 Audi R8 Launches all-LED Headlights
Audi became the first manufacturer to feature peripheral white LEDs as daytime running lights, first on the Audi A8 W12 in 2004 and then on the Audi S6, Audi R8 and Audi A5/S5 from 2006.
Audi is now premiering the first and only headlight unit in the world to deploy LEDs for all of the front lighting functions. Apart from the daytime running lights, these functions comprise the turn signals and the dipped beam and main beam headlights. Various groups of LEDs, known as arrays, produce the correct light distribution and brightness. Each headlight unit has a total of 54 LED light sources.
Read more
2000-2001 Audi TT Coupe Compact Disc Changer Installation Instructions
The following pages contain CD Changer installation instructions for the model listed above.
Rear seat, removal
– Remove rear seat bottom.
– Disconnect left rear seat belt at body anchorage point.
– Remove left rear seat back.
– Disconnect left front seat belt body anchor at floor (located at rear of front seat).
Read more
05 Audi A6 Electrics Service Training
The new Audi A6 – the most progressive vehicle takes the lead. The new Audi A6 consistently adopts the highly networked electronic architecture, which is already used in the Audi A8. Overall, new technologies allow the A6 to match up with its “model” vehicle, the Audi A8. Features, which were previously reserved for luxury vehicles, are now also available in the top-class segment.
Read more
1994 Ford Explorer Spindle & Shaft Assembly
SUSPENSION – FRONT (4WD COIL SPRING) 1994 SUSPENSION Ford Motor Co. Suspension – Front (4WD) Coil Spring Removal
1. Raise and support vehicle. Remove wheel assembly. Remove caliper from rotor. Remove locking hub.
See AUTOMATIC LOCKING HUBS or MANUAL LOCKING HUBS under REMOVAL & INSTALLATION.
2. Remove wheel bearings, lock nuts, hub and rotor. Remove spindle-to-steering knuckle nuts. Tap spindle
with plastic hammer to free spindle from steering knuckle. See Fig. 9 . Remove spindle, spindle seat (if
equipped) and splash shield.
3. On right side applications, remove and discard keystone clamp from shaft assembly and stub shaft. Slide
rubber boot onto stub shaft. Remove shaft assembly from right axle. See Fig. 9 .
Read more
1985-1996 GM Astro/Safari CMFI Assembly Repair Guide
The CMFI assembly is mounted to the lower intake manifold. The upper intake manifold assembly must be removed for access. The CMFI assembly includes a fuel meter body, gasket seal, fuel pressure regulator, fuel injector and 6 poppet nozzles with fuel tubes. Should a failure occur in any components of the CMFI unit, the entire assembly must be replaced.
1. Remove the plastic cover and properly relieve the fuel system pressure.
2. Disconnect the negative battery cable, then remove the air cleaner and air inlet duct.
3. Disengage the wiring harness from the necessary upper intake components including:
Read more
