2004-05 Chevy Colorado Prerunner Rear Bumper Installation
This kit should only be installed on a vehicle that is in good mechanical condition. Before installing the kit, replace worn or corroded parts. If the vehicle is suspected to have been in a collision or abused, DO NOT install the kit. The components in this kit do not eliminate weaknesses that may exist in the original equipment components.
Read more
2001-2004 Audi A6 4B C5 Single-Frame front bumper HF 7551 Installation Guide
1. Removal of the original bumper:
Remove all screws which hold the bumper. Also remove the screws which hold the alloy bar and remove the bumper with the alloy bar. Remove the alloy bar from the bumper and install it into the new Hofele-Design bumper.
2. Placement of the Hofele-Design front bumper on the car:
Place the new bumper on the car but do not yet bolt it on.
3. Preparation of the bonnet:
Remove the front grill and the rubber strap behind it. Install the front grill (HF 7052-S4 / RS4) in the extension piece.
Read more
350Z GT Aero Front Bumper Installation Manual
This product is meant to fit Nissan 350Z only. Please check the parts before mounting.
- Mounting Procedure
Please follow the manufacturer’s repair manual for proper front bumper cover removal procedure.
（Remove the side bracket from the OEM bumper. ）
(Remove the impact foam from the front of the bumper.）
Install the side bracket onto the GT bumper by reversing the steps used to remove it.
Install the GT bumper using the factory clips and screws to the original locations.
Read more
Audi HomeLink System (Europe) with the transmitter unit in the front bumper
The HomeLink system provides a convenient way to replace up to three remote controls with a single built-in component. This innovative feature learns the radio frequency codes of most current remote controls used to activate garage doors, property gates, security systems, and home or office lighting.
Read more
Complementing the 987C Boxster S with the 987A Cayman S Front and Rear Bumper Covers
Why change the Boxster S Bumpers? You fall in love with a Porsche—and start improving, modifying, and changing it until it reflects who you are. It doesn’t matter what kind of perfection you’re chasing. Porsche geekdom is one religion with many denominations: club racing, driver’s education, autocrossing, rallying, touring, preservations, concours, and socialization. If you don’t change it and make it uniquely yours, then you’re not really a Porsche guy, just a temporary owner.
Read more
88-98 Chevy Truck Installation Instructions Kit #10002 #10003
Do not attempt to tow with the vehicle bumper after the relocating brackets have been installed. These brack- ets are designed to enhance the appearance of the vehicle. Towing with the bumper after the brackets have been installed could result in vehicle damage, personal injury or death. All towing should be done with a class III receiver hitch only. The manufacturer is not responsible for any damage or injury resulting from towing with the bumper.
Read more
1993 Taurus/Sable Bumpers Removal and Installation
Bumpers Refer to the following illustrations when performing Removal and Installation procedures on the front and rear bumper assemblies. CAUTION: Never apply excessive heat to bumper surface. Heat could cause distortion of the bumper. CAUTION: When collecting exhaust fumes in service area, never attach a metal collector to the exhaust tail pipe because the heat could damage the bumper.
Read more
Audi A3 Sport Back 5 Door Hatch Installation
Installation Steps:
1) To remove the rear bumper, remove 3 torx screws from inside each wheel well. Remove both tail lights by using a socket through the port on the inside of trunk. Rotate light out of place carefully, so the tabs on the back side stay intact (rotate then pull straight out from the side to remove lens). Remove 2 torx screws from beneath each tail light (one short black, one long silver). Remove the 2 torx screws from the underside of the bumper. Remove (2) 10mm hex nut from the inside of the trunk using a deep socket, be sure to us a magnetic arm to catch the nuts ( remove the (2) round covers on the trim, then use a socket and extension to loosen bolts, then remove from rod with magnetic arm). Dettach the bumper cover from the side of the car, then pull straight backwards to remove.
Read more
1993-96 Chevrolet Beretta Baseplate BX1614 Installation Instructions
1. Read the General Instruction Sheet included with this baseplate.
2. The baseplate attaches to the engine mount braces under the car and to the bumper mounts using eight total bolts which are supplied with the baseplate.
3. Remove the headlight modules. The modules are attached with three screws at the top and back of the module. Remove the screws and pull the headlight forward to detach. Unplug the wiring.
Read more
Power IC System Nissan Silvia & 180SX – S13 Installation Manual
Thank you for purchasing the XS Engineering Power IC System for the Nissan Silvia & 180SX – S13. Utilizing state of the art design and manufacturing processes, XS Engineering has designed this Power IC System to complement the SR20’s inherent ability to operate at extreme boost pressure levels by allowing it to do so without penalty of increased intake air temperature. We strongly recommend that this kit be installed by experienced professionals only. This intercooler system includes piping for use with either the stock or stock replacement turbochargers only. You may have to modify the intercooler pipes if you are using an aftermarket turbocharger. Please take the time to read through and understand this manual fully before you proceed with the installation process.
Read more
