Audi A4 Avant Roof-edge Spoiler Fitting Instructions
The adhesive kit is not included. It must be ordered seperatly according to the parts List. For compliance with the TÜV certificate and ABE other adhesives are not permitted. The adhesive kit, comprising cleaner primer and P1 adhesive, is obtainable as part number 000 071 785 Please read fitting instructions thoroughly before commencing installation. We recommend that fitting of the roof spoiler is carried out by a specialist workshop.
Read more
Audi A3 Convertible SmartTOP Roof Top Control
Mods4cars, the southern California based specialist in high-end electronics for convertible top and remote controls, announced the release of their latest “SmartTOP” comfort roof top control for the new Audi A3 convertible. Customers are now able to raise and lower their convertible top at the touch of a button while driving at low speed or remoteley using their factory key fob.
The new T-Adapter saves 50% installation time. The adapter is included at no extra cost. It allows an simple plug-and-play installation of the SmartTOP module without the need to remove single contacts from the plug. Also, the original condition can easily be restored in seconds.
Read more
1994–2003 Ford Powerstroke 7.3 liter Vehicle Programming Instructions
The following manual contains information and instructions on the proper use of Evolution. Please read carefully before proceeding to program your vehicle. Note: Read the product disclaimer before programming your vehicle.
TOW Program
This setting is the lowest level setting, but still increases your horsepower and torque
Read more
Audi A3/A4 M4C-STA4 Comfort Roof Control Module Installation
Installation – Steps 1-3
1. Turn the ignition on and open the roof completely. Then start closing the roof and stop when the rear lid is fully open (vertical position). This enables access to the area marked (2). IMPORTANT: Turn off the ignition and remove key before continuing! Remove rear seat bench (lift up front portion with force), then remove T-30 torx screw (1).
2. Remove rear side panel: First pull towards the center of the car (1) then lift up and slide up and frontward out. Simultaneously pull the back rest up (where the torx screw was removed earlier). The side panel is just snapped into place and can be lifted off along the rubber edge (2). Directly behind the panel is the roof controller box.
Read more
Federal Motor Vehicle Safety Standards Roof Crush Resistance
The purpose of Federal Motor Vehicle Safety Standard (FMVSS) 216 is to reduce deaths and serious injuries when vehicle roofs crush into occupant compartments during rollover crashes. The National Highway Traffic Safety Administration (NHTSA) has issued a supplemental notice of proposed rulemaking (SNPRM) for this standard, asking for comments on additional tests conducted by the agency since the 2005 notice of proposed rulemaking (NPRM). The Insurance Institute for Highway Safety (IIHS) does not believe the additional tests provide meaningful information for a standard requiring two-sided testing.
Read more
Transponder Bypass for Honda ET Acura (2 programmable modes)
You must use the Black key to complete the programming procedure. Programming : Keep the programming button pressed down while inserting the wire harness into connector of the HONDA-DA. Release the programming button once the LED turn ON. Turn the Ignition to the ON position. The number of LED flashes indicates the mode. (I.e. Mode 1 = 1 Flash) Press the programming button to switch between modes 1, 2 and 3. (Mode 3 is future use) Once the mode is selected, turn the ignition key to OFF position. Turn the IGNITION key to the ON position once again. The LED will illuminate. The module is now programmed. Turn the key to the OFF position and remove it, start the vehicle using the remote starter to insure functionality.
Read more
BMW 3 E93 Convertible Comfort Module Installation
The module only uses functions which were originally built into the vehicle. All data relevant to convertible top control (e.g. limit switches, window position, speed) will be continuously monitored. All OEM safety functions (under / over voltage cut-off, thermal protection, etc.) remain intact.
Read more
2004-2005 Cadillac CTS-V JET Performance Products Installation
INSTALLATION INSTRUCTIONS OVERVIEW
Your vehicle has an onboard computer that controls the engine and transmission. The JET programmer reprograms your factory computer according to your specifications with JET Performance Products Tuning.
To reprogram your vehicle’s computer, simply plug the programmer cable into the vehicle’s diagnostic connector, located under the dash panel on the driver’s side. Set the parking brake. Next, turn the ignition key to RUN but do not start the engine. It will then identify your vehicle and ask a series of questions on its LCD screen. When completed, turn the key to OFF and disconnect the cable from the diagnostic connector. Now you’re “Engineered for Power”.
Read more
Toyota/Lexus 1100X/f-tl Transponder Bypass Type 1 & 2 Installs
The 1100X/F-TL interface module is used when installing remote start products in Toyota/Lexus vehicles equipped with a factory immobilizer. The 1100X/F-TL allows for easy interfacing between the remote start and the factory immobilizer, while maintaining the integrity of the OEM sys- tem. The factory transponder-based anti-theft system uses a small elec- tronic chip hidden in the key to send a code to the vehicle’s transceiver when the ignition is energized. The key must be placed in the ignition and turned to the RUN position. This energizes a coil surrounding the key, which in turn energizes the chip, which sends a code to the vehicle. If the vehicle does not detect the code being sent, the vehicle will start and then immediately shut off or will just crank, and the anti-theft light will flash. The 1100X/F-TL provides a valid code to the vehicle whenever it is remote started, but does not affect the immobilizer system during normal vehicle operation; the immobilizer system remains fully functional.
Read more
Honda/Acura Transponder Interface Firmware: PKH3
WIRE GUIDE: CONNECTIONS
10 PIN HARNESS
D2D = Optional use of 4 Pin Data to Data (D2D) cable will replace the analogue wire (w2w) connection
DATA to DATA PORT (D2D): Blue connector of D2D Cable plugs into the upgradeable vehicle interface module.
OPTION A: – D2D Port used to connect to USB Bootloader adaptor & computer to download & flash vehicle interface firmware.
OPTION B: – D2D Port used to connect to the data port of a remote control system equipped with ClearCode Vehicle Interface Protocol. Read more
