06-UP BMW E90-E93 Rear Camber Link Kit Installation
Installation of Rear Camber Links
1. Raise vehicle and support with jack stands. Remove rear wheels. Place jacks under the rear lower control arms, and jack up slightly to take load of the upper control arms.
2. Remove the ABS wire retaining clip from the upper control arm.
3. Remove the bolts that attach the upper control arms to the knuckle and to the sub-frame, and remove the control arms.
4. Place the factory control arms next to the new double adjustable control arms. Adjust the new arms to the same length as the factory Read more
1993 Jeep Grand Cherokee Wheel Alignment
WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES 1993 WHEEL ALIGNMENT Chrysler Corp. – Specifications & Procedures
ADJUSTMENTS CAMBER MEASUREMENT
Check camber to determine if any components are bent or damaged. Camber angle is NOT adjustable. If angle is not to specification, components causing problem must be replaced. See ALIGNMENT SPECIFICATIONS .
CASTER ADJUSTMENT
Check caster angle. See ALIGNMENT SPECIFICATIONS . If caster is not to specification, adjust by adding or removing shims at rear of lower control arms on all except Wrangler, or between front axle pads and spring brackets on Wrangler. See Fig. 1 or Fig. 2 .
Read more
1998-2002 Ford Ranger 2 Wheel Drive Upper Ball Joint Replacement
O.E.M. supplier sells the upper ball joint as an arm assembly; we sell the ball joint only which can be pressed out of the arm assembly. Repair Procedure: 1. Raise vehicle on hoist, and support lower control arm. 2. Remove wheel and tire assembly. 3. Mark position of upper eccentric camber bolts. 4. Remove upper ball joint spindle nut and pinch bolt, 5. Separate upper ball joint from spindle. 6. Remove nuts and camber bolts attaching upper control arm-to-frame, 7. Remove upper control arm. 8. Place control arm in vise, press ball joint out with ball joint press. See Read more
BMW Concept X6
BMW presents the concept car X6 on this years IAA in Frankfurt, Germany. They created a new category of car, the Sports Activity Coupé. The car is 4.88 m long, 1.98 m wide and 1.70 m high. As it was with former shown concept cars (M5 and M3), it’s probable, that also the Concept X6 is going to be in production nearly unchanged.
Read more
1993 Ford Explorer Suspension Front (2WD) Removal & Installation
The first step of removal the spindle from this ford explorer
Removal 1. Raise and support front of vehicle. Remove wheel and tire assembly. Remove brake caliper from rotor and wire it to under-body to prevent damage to brake hose. 2. Remove dust cap, cotter pin, nut retainer, nut, washer and outer bearing. Remove rotor from spindle. Remove inner bearing and seal. Discard seal. Remove brake dust shield. 3. Remove tie rod end from spindle arm with Tie Rod End Remover (Tool-3290-D). Remove cotter pin from lower ball joint stud. Remove axle clamp bolt from axle. Note position of camber adjuster on top of axle. 4. Using Ball Joint Remover (D81T-3010-B), remove camber adjuster from upper ball joint stud and axle. Strike inside area of axle to release lower ball joint. See Fig. 4 . Remove spindle and ball joint assembly from axle.
CAUTION: DO NOT use pickle fork to separate ball joint. This will damage the seal and ball joint socket.
Read more
2007 Audi Q7 4.2 Quattro Premium
With a host of innovative extras included as standard equipment – including Rear View Camera with Acoustic Parking – the Audi Q7 4.2 Premium model delivers superb power, efficiency, and control via a 350 hp 4.2 V8 equipped with FSI® Direct Injection technology, and combined with quattro® all-wheel drive and a 6-speed Tiptronic® transmission. More pictures below…
Read more
2002 Toyota Tacoma Crankshaft Position Sensor ”A” Circuit Malfunction Diagnostics
The crankshaft position sensor, which detects the engine speed and crankshaft angle signal (NE signal), has been installed on the oil pump body. The NE signal plate has 34 teeth. The NE signal sensor generates 34 signals at every engine revolution. The ECM detects the standard crankshaft angle based on the G signal, and the actual crankshaft angle and the engine speed by the NE signal.
Read more
2000-2003 Mitsubishi Eclipse Adjustable Coilover Kit
Spring height adjustment:
This coilover kit is designed to allow both race-ride and street-ride heights. It is not recommended to run race-ride height for normal street driving. This will result in more tire wear due to the excessive negative camber, which creates more stress on the wheel hubs and ball joints.
With the vehicle jacked up and secured on jack stands, raise (clockwise) or lower (counter clockwise) the aluminum perches with the supplied spanner wrenches to the desired height. Depending on which way turned, securely tighten the other perch against it. Lower the vehicle to check ride height. This processed may need to be repeated until the desired ride height is achieved. Camber and toe settings will change depending on the height adjustments. A wheel alignment is recommended after complete installation.
Read more
2007 H&R Volkswagen Project GTI 250hp
VW introduced the first pocket rocket and started a niche market that is now a style statement for many car enthusiasts. We wanted to build a car that let the best of the GTI and the best of the aftermarket kick asphalt! The H&R Project GTI has something for all. It is subtle, but different. The tone on tone paint difference is not always noticeable, but the power and handling definitely is! The new GTI has an automatic built-in market. The young car guys who built GTIs 25 years ago cant wait to get their hands on this new car. The Y Generation likes a well-engineered vehicle that offers a huge array of aftermarket to add to their style. H&R GTI has it all!
Read more
1960-66 Ford Pickup Mustang II Independent Front Suspension
Installation of Full Tilt Street Rods’ Crossmember Kit is easy because we have designed all the correct angles onto our crossmember. You must make a couple of measurements to correctly place the crossmember and spring mounts before welding. Minor adjustments may be needed for some variations in your frame. We recommend that all welding be done by a qualified welder using accepted procedures.
Read more
