2009 – 2010 Cadillac CTS-V Installation Guide – HPE Cold Air Intake
Step 1: Remove Factory Air Intake Assembly
Removal of the factory air intake assembly is straightforward. Start by removing the surrounding plastic covers and placing them somewhere out of the way so as not to cause any damage and provide ample working space. Using basic tools, disconnect the intake from the throttle body, unclip the mass airflow (MAF) sensor and disconnect the breather hose. Remove the factory air filter and air box, revealing an opening to the lower fender wall. This is where your new air filter will be placed in order to draw in cooler air.
Read more
2003-2005 Mazda 6 s V6 Cold Air Intake System Installation
DO NOT install a bypass valve on this intake! Following is the procedures to installation the AEM Cold Air Intake System on your Mazda 6.
Getting started
a) Make sure vehicle is parked on a level surface.
b) Set parking brake.
c) Disconnect both battery terminals.
d) If engine has run within the past two hours let it cool down.
e) Chock rear wheels, jack up front of vehicle and place on properly rated jack stands.
f) Remove front left wheel.
Read more
2000-02 Audi TT 1.8T FWD/Quattro Dyno-Proven Cold Air Intake Installation
Before installing any parts of this system, please read the instructions thoroughly. If you have any questions regarding installation please contact the dealer you purchased this product from. Installation DOES require some mechanical skills. A qualified mechanic is always recommended.
*Do not attempt to install the intake system while the engine is hot. The installation may require removal of radiator fluid line that may be hot.
Read more
1998-2002 Chevrolet Cavalier Cold Air Intake System Part Number 21-447
The AEM Cold Air System is the result of extensive development on a wide variety of cars. Each system is engineered for the particular application. The AEM Cold Air System differs from all others in several ways. We take the inlet air from outside of the engine compartment where the inlet air is considerably cooler than the hot under hood air. The cooler inlet air temperature translates to more power during the combustion process because cool air is denser than warm air. AEM has conducted extensive inlet air temperature studies and we have seen temperature reductions of up to 50 degrees by pulling air from outside of the engine compartment. The air mass flow to the engine is increased because of the increased airflow and reduced inlet temperature, which translates to more power.
Read more
Honda Civic Si & Acura RSX Icebox Cold Air Intake Installation Instructions
Comptech Icebox Cold Air Intake for the 2002–2005 Honda Civic-Si and 2002–2005 Acura RSX. All components have been designed and manufactured utilizing the latest in technology and materials. Comptech recommends that you read through these instructions before starting installation and that you use an Acura Factory Shop Manual to supplement these instructions. All Comptech products are intended to be installed by a professional installer. Always use jack stands to support the vehicle when a car lift is not available. Always work in a clean environment and use the appropriate safety equipment to avoid any potential damage or injuries.
Read more
2002-04 Nissan Altima Dyno-Proven Cold Air Intake System Installation
All 2004 vehicles that are considered LEV2 and SULEV with engine test group numbers of families do not satisfy or meet the California air resource board tet procedures. The engine group test numbers can be found on the underhood information label located on the drivers side. Engine test group numbers listed below are to be considered for off-road use only: 2004 Nissan Alima 2.5L test group number- 4NSXV02.585A
Read more
Cold Weather Hard Steer Tech Tip
Hard steer during cold start-up has been a frustrating problem with power racks since the beginning. GM has had its fair share of cold steering problems that would subside moments later, and the system would return to normal power assist. Internal seal seepage or leakage has been a problem since the early 80’s. Revised seals were made available, and eventually new rack assemblies were recommended for those with worn or grooved housings, thus promoting internal leakage.
Read more
2010 Honda Accord Crosstour Typhoon Intake System Installation Instructions
69-1210 HONDA 2008-10 Accord 2010 Accord Crosstour V6-3.5L
1. Turn off the ignition and disconnect the negative battery cable.
2. Disconnect the positive battery cable, remove the battery hold down and then remove the battery.
3. Disconnect the mass air sensor electrical connection.
4. Disconnect the crank case vent tube from the in- take tube and valve cover port as shown. The spring clamps will not be reused.
5. Loosen the hose clamp which secures the stock intake tube to the throttle body.
Read more
2010 Audi A4/S4 Media Information
The Audi A3 has both pioneered and led a new premium compact car segment since its U.S. introduction in 2005. In 2009, worldwide sales of the successful A3 had exceeded 1.9 million, and that number continues to swell today. To ensure that the 2010 A3 stays ahead of the ever-growing pack, Audi has made available a number of upscale features, including upgraded wheels and standard Xenon headlights with LED daytime running lights on Premium Plus models. Every 2010 A3 showcases the sporty Audi DNA with S line exterior upgrades now standard on Read more
2008 Dodge Viper V10-8.4L K&N Drycharger Intake System
The K&N® Drycharger® included with this kit must be installed on the K&N® air filter when used with this K&N® cold air intake system. The K&N cold air intake system a performance product that can be used safely during mild weather conditions. During harsh and inclement weather conditions, you must convert your cold air intake system to a short ram configuration, or return your vehicle to the stock OEM air box and intake tract configuration. Failure to follow these instructions can void your warranty.
Read more
