1999 Ford Ranger Trucks Gasoline Engine Performance Removal
Removal & Installation (3.0L, 3.8L, 4.0L & 5.0L) 1. CMP sensor is located on top of engine, near intake manifold. See Fig. 3 Fig. 3: Locating Camshaft Position (CMP) Sensor (3.0L, 3.8L, 4.0L & 5.0L; 4.2L Similar) Courtesy of FORD MOTOR CO. 2. Disconnect negative battery cable. 3. Before removing, note position of electrical connector on CMP sensor. Disconnect CMP sensor electrical connector. NOTE: For Explorer models with 4.0L push rod engine, remove the upper intake manifold. See REMOVAL & INSTALLATION (4.0L VINX) under UPPER INTAKE MANIFOLD. 4. Remove CMP sensor screws and CMP sensor. To install, reverse removal procedure. Ensure CMP sensor electrical connector is pointing in original direction. Tighten CMP sensor to specification. See TORQUE SPECIFICATIONS . NOTE: If the synchronizer is turned while removing the CMP sensor, it must be re-aligned before CMP sensor is installed. See CMP.
Read more
2006-2009 Toyota Camry Harsh 5-4 Downshift on Deceleration
Some 2006 – 2009 model year Camry vehicles equipped with the 2AZ-FE engine and U250E automatic transaxle (ATM) may exhibit a harsh 5–4 downshift under the following conditions: • ATM at normal operating temperature • After driving above 45 mph (72 km/h) • Decelerating through 28 mph (45 km/h) The line pressure control solenoid assembly (SLT) has been improved to reduce this condition on customer complaint vehicles.
Read more
2007 Toyota Camry/Camry HV Interface Kit For iPod
Vehicle Disassembly (a) Set parking brake. (b) Remove the negative battery cable. (Fig. 1-1) (1) Protect the fender before starting. (2) Do not touch the positive terminal with any tool when removing cable. (c) Remove instrument panel garnish LH: (1) Disengage the 2 clips and remove the instrument panel garnish. (Fig. 1-2) NOTE: Pull the instrument panel garnish up at a 45º angle to remove it. (d) Remove instrument panel garnish RH: (1) Disengage the 2 clips and remove the instrument panel garnish. (Fig. 1-3) (e) Remove floor shift position indicator for automatic transmission. (1) Unscrew shift knob. (2) Disengage the 6 claws and 3 clips and remove assembly. (Fig. 1-4) (3) Disconnect any connectors. (f) Read more
X431 Connector Guide
A few rules of thumb:
1. If the car has an OEM-style connector which is included in the X431 and an OBD-II connector, the OEM-style will usually provide the most capabilities for accessing OEM data.
Current examples are:
-Mercedes 38
-BMW 20
-Subaru 9
-Kia 20
-Mazda 17
-Nissan 14+16
-Mitsubishi/Hyundai 12+16
-Toyota/Lexus 17
Read more
2003 350Z MIL ‘ON’ DTC P0442 (Evap Small Leak) Stored In Self Diagnosis Results
An Applied Vehicle has a MIL “On” and has one or both of the following DTCs stored in the ECM:
• P0442 EVAP Small Leak
• P0456 EVAP Very Small Leak
ACTIONS:
Confirm this bulletin applies. Perform CONSULT-II Self-Diagnosis (repair as needed). ECM Part Number Check to determine if this bulletin applies. ECM Reprogramming (needed if a match is found during ECM Part Number Check).
IMPORTANT: The purpose of “ACTIONS” (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire Service Procedure (starting on page 2) as it contains information that is essential to successfully completing this repair.
Read more
Toyota Torque Converter Operations and Diagnosis
TORQUE CONVERTER BASICS (Using a 2003 Camry/Solara as our example)
Mounted on the input side of the transmission, the torque converter is connected to a drive plate (or flex plate) that is connected to the rear of the crankshaft. The torque converter (which is filled with automatic transmission fluid) multiplies Read more
Mopar Remanufactured Single Board Engine Controller (SBEC) Removal & Installation
This MOPAR Single Board Engine Controller is warranted by Chrysler Corporation against defects in workmanship or materials for 12 months or 12,000 miles, whichever comes first, from the date of its installation into a Chrysler, Plymouth, Dodge, Jeep or Eagle vehicle. If it fails, it will be repaired or replaced, at the option of Chrysler Corporation. To obtain service under this Limited Warranty, return the module to an authorized Chrysler Corporation Dealer.
Read more
2005-2008 Ford Mustang Edelbrock Coupe Sub-Frame Connector
Designed to fit 2005-2008 Ford Mustang Coupe, Edelbrock sub-frame connectors are stronger and more effective due to (1) Large welded surface area, (2) connects rear suspension connection point to engine cradle and front K-member, (3) ground clearance is minimally affected.
Read more
1992-96 Toyota Camry Pro.Fit Part Number TY-50-92 Installation Instructions
All instructions assume a drivers seat vantage point. Caution is advised when removing and reassembling wood or plastic parts of a dash. Applying unnecessary force or pressure may cause a piece to crack or break. Pro.Fit logo and part number will be right side up and readable when installed.
TOOLS REQUIRED: #2 Phillips screwdriver, hook tool.
PARTS INCLUDED: Pro.Fit VSMTM, instructions.
LOCATION: To the right of the radio.
Read more
Remote Starter Integration for the 2007 Toyota Camry equipped with the Smart Key System with Push Button Start
Preparation the Toyota Camry for installation
-Remove the driver’s side under dash, as well as the knee airbag bolts. Move the Airbag aside, but DO NOT DISCONNECT the Airbag connector in order to avoid setting any vehicle codes.
-Remove the driver’s side floor heating duct, in order to access the vehicle IMI & IMO wires easily.
The remote car starter will be installed in a conventional manner even if the car is equipped with the Smart Key “Push-to-Start” system.
Read more
