Ford Escort IV 3/5 Doors Towing Hitch Fitting Instructions
This towing hitch is designed to assembly in following cars: FORD ESCORT IV 3/5 doors, produced since 01.1996 till 1998, catalogue no. C10 and is prepared to tow trailers max total weight 1250 kg and max vertical load 50 kg.
1. It is not necessary to reassemble the bumepr.
2. Find original signed places inside the boot on the left and right side, then drill ø24mm.
3. Slide the sleeves L=50mm (pos. 5) and position the element (pos. 4).
Read more
1991-96 Ford Escort Baseplate BX2112 Installation Instructions
Installation of this baseplate requires removing the plastic belly pan. The brackets attached to the vehicle’s frame and the tie down brackets also need to be removed. They will be replaced with the baseplate’s side mounts. The plastic around the tie down brackets will need to be trimmed.
1. Read the General Instruction Sheet included with this baseplate.
2. Under the front corners of the car there is a stamped metal bracket that protrudes down with a slot at the bottom. These are called the tie down brackets. The baseplate mounts to the outside of the tie down brackets and to the center engine support bolts, using ten bolts, eight of which are supplied with the baseplate.
Read more
2001 Mercedes Benz E 320 Sedan V6-3.2L Door Liner on Rear Door Remove/Install
Removing/Installing
1. Press of handle recess (3) using assembly wedge
2. Unscrew screw (4) in the area of the interior door control
3. Unclip cover (11) and unscrew screw (12) With code 293 (rear side airbag)
4. Unscrew screw (1) on lock escutcheon (2) and remove lock escutcheon (2) downwards
5. Press of cover (5) under armrest and unscrew screw (6)
Read more
1991-1996 Ford Escort Radio Replacement
STEP 1: The Ford radio is snapped into the vehicles dash. With the proper tool, known as Ford radio removal keys, the Ford radio can be pulled forward out of the dash. A clothes hanger can be used instead of actual Ford radio removal keys. Cut the clothes hanger and bend 2 pieces in the shape as shown in the photos above. For more information on how to remove the radio, see the diagram below.
Read more
1992-2001 Ford Escort/ZX2 Short Throw Shifter Installation
This B&M Short Throw Shifter has been designed to work on most 1992 – 2001 Ford Escort/ZX2, 1992-1999 Mazda MX- 3/30X, 1992-1994 Mazda 323, and 1992-2002 Mazda Protegé/MP3/5 models. It has been engineered to greatly reduce shift throw and improve shifter feel. Check the parts and tools lists at the beginning of these instructions for the supplied parts and the tools required to install your B&M Short Throw Shifter. Installation of the B&M Short Throw Shifter can be accomplished by anyone with minimal mechanical experience.
Read more
2001 Ford Taurus V6-3.0L VIN U Front Door Trim Panel Installation
Removal and Installation
1. Disconnect the battery ground cable.
2. Remove the front door trim panel screws.
3. NOTE: The front door trim panel has five two-part pin-type retainers. Then male part of the trim retainer will remain with Read more
2004-2006 Ford F-150 Liquid Solid Billet Door Handle Instruction
The installation of the replacement door handles are for persons with advanced auto-body skills and is recommended to have them professionally installed.
A. Pre-installation Preparation
Step 1: Verify kit contents.
Step 2: Remove the door handles from the box.
Step 3: Make sure the window is up and the door is unlocked.
Read more
1996-2000 Honda Civic Vertical Door Installation
1) Disconnect the battery. 2) Remove fender: Remove all Phillip’s screws from the wheel well. Remove (1) 12mm bolt to loosen the bumper. Once the 12mm bolt has been removed pull on the bumper and remove (2) 8mm bolts from behind the bumper. Remove (3) 8mm bolts form the top of the fender. Remove (2) 8mm bolts from the bottom of the fender by the door. Remove (1) 8mm bolt holding the fender. At this point you should be able to remove the fender. 3) Remove the door catch: Open the door and remove (1) 10mm bolt from the body and (2) 10mm from the door. Push the door catch inside the door. 4) Gaining wire slack: Remove foot trim, under it you will find (2) wire harness use the Read more
1986-1990 Ford Escort Estate/Combi Van Towbars FD2266 Fitting Instructions
FITTING PROCEDURE
- Remove the spare wheel.
- Locate the two holes in rear chassis and drill up through the top skin at 11mm diameter. (Do not drill through the floor
– Remove the rear lights to access top of chassis). Open out the bottom holes just enough to accept spacer tubes (D) and use bolts (G) to fasten crossbar (B) in place with spacer tubes (D) in the chassis and the square washers (K) above the chassis.
- Fasten towbar (A) to crossbar (B) with bolts (H).
- Centralise the assembly and drill at 13mm diameter through centre hole into boot floor. Use bolt (F) to fasten crossbar (C) in place through Read more
2007-2009 Jeep Wrangler 4-Door and 2-Door Audio System Upgrade Package
Radio Removal
1. Using a panel removal tool pry up on the plastic trim panel located above the radio. Make sure to pry on the side of the panel closest to the window.
2. Using a panel removal tool pry loose the top edge of the panel below the HVAC controls.
3. Using a 7mm nut driver remove the four screws securing the radio trim bezel. There are two at the top and two at the bottom.
4. Starting at the top and working your way down pull out on the trim bezel to release the fasteners securing it. Once the bezel is completely detached from the dash it is not necessary to disconnect any of the wiring or the HVAC linkage. Simply allow the bezel to rest on the console to allow access to the screws securing the radio.
Read more
