Audi Gateway 500 with Dual FOT Installation
Installation of GATEWAY 500 unit Dual FOT
For All Audi vehicles: A good location to mount the GATEWAY 500 unit is at the CD Changer behind the glove box. If the vehicle is equipped with the in-dash CD Changer, install the GATEWAY 500 unit behind it. Interfacing in the MOST optical ring should be done as shown in the installation guide.
For All Audi vehicles NOT equipped with a factory CD Changer, the GATEWAY 500 interface shall be integrated into the optical MOST ring at the output of the head unit.
For All Audi vehicles equipped with a factory CD Changer, the GATEWAY 500 interface shall be installed at the factory CD Changer location
Read more
Audi V1 Interface and V1 Power Hardwire Installation Guide
Installation with V1 hardwire
Requirements:
Audi vehicle with CAN bus or CDE interface for instrument cluster radio information.
Steering wheel buttons, TAPE button or additional wired button.
V1 Radar Detector
V1 Direct Power Adapter
2 straight 4 conductor RJ11 cables (like the ones included with the V1)
A-B USB cable for updating and setup
Read more
FISCON Pro Hands free kit Installation Manual for Audi
While developing this product, your personal safety combined with the best operating service, modern design and an up-to-date production technique was especially taken into account. Unfortunately, despite the utmost care injuries and/or damages might occur due to improper installation and/or use. Please read the attached instruction manual completely with great care and keep it! All articles of our production line pass through a 100 % check – for your safety and security. We reserve the right to carry out technical changes which serve the improvement at any time. According to each article and purpose, it is sometimes necessary to check each country’s legal regulations before installing and starting the unit.
Installation instruction
1 – CD device Audi A4 8K, A5 8T, Q7 4L
2 – CD device Audi A6 4F /
2 – AMI Audi A6 4F, A4 8K, A5 8T
3 – Telephone interface (behind the glove box)
4 – Microphone (Interior light)
Audi A4 8K, A5 8T
Loosen the necessary screws of the glove box (Fig. 9 – 11). Disconnect the original wiring of the CD/AMI device (if available).
Remove the cover shown on figure 12. Mount the interface to the back of the glove box by using suitable fastener
Remove the airbag sign by using suitable tools (in order to avoid damages) and loose the screw located behind.
NOTE: Does the vehicle have airbags fitted along the A-column it is essential to wire the loom for the microphone BEHIND the airbag. Wire the loom without putting tension on it. Mount the loom without affecting the airbag in it’s functionality.
Open the storage of the interior light and loose the screw (Fig. 19). Mount the microphone on the original location within the interior light – driver’s side
Audi A6 4F
Loosen the necessary screws of the glove box (Fig. 22, 23). Disconnect the original wiring of the CD/AMI device (if available). Mount the interface to the back of the glove box by using suitable fastener.
2002+ Audi A4 FWD/QUATTRO Street Sport Coil Over kit Installation
Before removing any parts, park the car on a secure, stable and level surface, loosen (but do not remove) the wheel lug nuts, jack the vehicle up and place the car on four stable jack stands or use a professional vehicle lift. We recommend having two people available for certain steps of the installation.
Front Install Instructions
1. Securely support both front corners of the car (relieving tension on the ARB).
2. Remove front wheels.
3. Remove Clip #1 using pliers. You do NOT need to reinsert this clip. Unfasten Nut #2, take out the hex bolt and pull both links upward and out.
Torque Spec: 40Nm.
4. Unscrew hex bolt (shock clevis) from suspension and control arm. Torque Spec: 90Nm with vehicle out or near ride height (use a transmission jack or floor jack)
5. From within the engine bay: Remove Cover to gain access to upper mount bolt.
6. Unscrew hex bolts #1 within engine bay. Take care not to damage the boot when remove bolts. Remove Front assembly from vehicle.
Read more
Audi A6/A8/Q7MMI CT90-AU06 Multimedia Interface Installation
This interface allows additional video inputs to the original MMI screen;
2 Video inputs/Automatically switchable camera input/ RGB Navigation input
There are also 2 video outputs and an audio output.
Selection can be made by infra red remote control or by the Nav button in the vehicle.
The remote control can also be used to adjust the picture via an on screen menu.
If a camera and reverse signal wire are connected it will automatically switch when the vehicle is put into reverse gear.
The vehicle shown in the installation instructions is a 2006 Audi A6 LHD. The installation and locations of units in the A8 and Q7 will be similar.
During the installation it is advised that the keys are removed from the ignition, until all components are reconnected.
Read more
1996-2000 Audi A4 Short Throw Shifter Installation Instructions
This B&M Short Throw Shifter has been designed to work on most 1996-2000 Audi A4, 2000 Audi S4, 2000 Audi A6, and 1996-2000 Volkswagen Passat models. It has been engineered to greatly reduce shift throw and improve shifter feel. Check the parts and tools lists at the beginning of these instructions for the supplied parts and the tools required to install your B&M Short Throw Shifter. Installation of the B&M Short Throw Shifter can be accomplished by anyone with minimal mechanical experience.
Read more
VW/Audi Quick Fit Rallye 4 Harnessbelts Installation
SCHROTH VW/Audi specific asm-Rallye 4 Series harnessbelts are only intended for installation at the left and right outboard front seating positions of designated VW/Audi model passenger cars which have been specifically evaluated by SCHROTH engineers for anchor point locations and suitability of available front seats. Before attempting installation, please first answer the following questions and carefully follow the instructions which accompany them.
Read more
2004+ Audi A6/A8/Q7 NV_AUDIA6A8 Nav Video Installation Guide
Warning
1. Before working, please make sure the vehicle power is off (please keep in mind when pulling out the
key, only monitor supply would be off but whole vehicle power supply would be off 5 minutes later).
2. Starting with separating of the monitor and the connecter removed in working may causes an error code. Do not start until the work is done.
3. Please use appropriate measure of tools
4. Do not force excessively in assembling or disassembling, tightening or pulling
5. Using protecting clothes or taping around the working area, take care of scars
6. Please make sure to connect the power cable using a fuse when you use it with pulling out the power supply.
Read more
Audi TT 8J Roadster A3 Cabriolet Convertible Top interface Installation Guide
Convertible top interface
• Convenient interior (one-Touch) operation – Control with the remote – Fully automated opening and closing.
• Usage of original connectors.
• Operate while driving up to the pace of 60 km/h (50 km/h to 60 km/h).
• Indication of opening and closing convertible top by flashing indicators (optional).
Read more
2007 Audi Metroproject Quattro Concept
The Audi Metroproject Quattro, has a battery pack in visibly mounted in the boot, and lit in tranquil blue lights with a charge indicator on the side.
The supermini Audi A1 should be available with a turbocharged gas engine, turbocharged diesel engine, ranging in size from 1.2 litres to 2.0 litres. A base model with an 80 horsepower, naturally aspirated 1.4 litre engine is also expected to hit showroom floors.
Read more
