MMR-1/MMR-2 Digital Rear View Mirror with Temperature and Compass Installation
You may following below steps to complete the installation:
1. In the interior of the vehicle, remove the upper windshield trim, the driver’s side A-pillar trim and kick-panel (plastic trim panel on the floor by your feet).
2. Remove the factory rearview mirror from the windshield.
3. Install the new mirror.
If the mirror does not fit your vehicle, it may be necessary to replace your mirror button with a different one. Pre-1996 Ford units are a commonly compatible style.
4. Starting at the bottom of the dash on the driver’s side, feed the black, flat connector up to the opening for the A-pillar at the base of the windshield. Routing the wires straight up the pillar, pull enough through to reach the mirror.
Read more
1998 Mercedes Benz SLK 230 L4-2.3L SC Rear Center Console Remove/Install
Removing And Installing Rear Center Console
Removing And Installing Front Center Console
AR68.20-P-2350G Remove/Install Cover on Center Console
Removing And Installing Cover On Center Console
Read more
2008 Toyota Highlander EC Rearview Mirror
Steps for EC Rearview Mirror installation: 1. Remove Battery Cable. (a) Protect fender before starting. (b) Do not touch the positive terminal with any tool when removing cable. (c) Remove the negative battery cable. (Fig. 1-1) 2. Vehicle Disassembly. (a) Remove the OE mirror. (1) Disengage the two claws and remove the mirror cover from the mirror base. (Fig. 2-1) (2) Pull the lever in the direction indicated by the arrow shown in the illustration and slide the inner rear view mirror assembly upward to remove it. (Fig. 2-1) (b) Using panel removal tool remove overhead console from headliner. (Fig. 2-2) (1) Disconnect any connectors connected to the overhead console. 3. Install T-taps. (a) Locate the disconnected 22-pin overhead console connector. (Fig. 3-1) (b) Peel back or cut approximately one inch of the wire cover. (Fig. 3-2) (c) Read more
2001 Mercedes Benz E 320 Sedan V6-3.2L Door Liner on Rear Door Remove/Install
Removing/Installing
1. Press of handle recess (3) using assembly wedge
2. Unscrew screw (4) in the area of the interior door control
3. Unclip cover (11) and unscrew screw (12) With code 293 (rear side airbag)
4. Unscrew screw (1) on lock escutcheon (2) and remove lock escutcheon (2) downwards
5. Press of cover (5) under armrest and unscrew screw (6)
Read more
1996-2000 Honda Civic EX, GX, LX Sedan Signal Mirror Installation Instructions
Door panel removal
1. Open door and lower window.
2. Remove screw from center of armrest and remove armrest from door.
3. Disconnect wire from behind window control panel.
4. Remove screw from behind door handle and remove door handle cover.
5. Disconnect wire from behind door handle cover.
6. Remove speaker cover.
Read more
2007 Freelander 2 SE Rear Screen Connectivity Aftermarket Install Guide
I have just finished fitting the rear screen connectivity system to my car. I was going to do a photo album of the install, unfortunately the camera died after the second photo. Instead I have used pics from the installation instructions and workshop manual to help illustrate.
Typical Land Rover, the instructions that came with the kit where pictorial only, and not as clear as they could have been (in my humble opinion). I hope this installation guide will be a lot easier to follow and hopefully you won’t have the few problems I encountered.
Read more
Chevy Silverado 1999-2005 Signal Mirror Installation Instructions
Mirror Housing Removal
1. Open driver side door. Lower window.
2. Remove door lock cover.
3. Unsnap and remove the triangular molding that covers the mirror mounting screws.
4. Unsnap and remove the molding that covers the door handle. Remove the screw behind the door handle.
5. Unsnap the control console and unplug the wires. Remove the screw located behind the arm rest.
6. Dislodge the door panel by pulling it up and away from the door slightly. Disconnect light and tweeter connections and remove door panel.
Read more
Gentex Mirror Installation Instructions
Instructions for Universal Harness
These instructions have been prepared to provide you with details necessary for complete installation of the Gentex Aut o Dimming Mirror, Gentex Auto Dimming Compass/Temperature Mirror, or Gentex Auto Dimming/Compass/Temperature Mirror with Map Lights. Be sure to read all instructions prior to beginning the installation. Follow all the safety guidelines outlined in this instruction book as well as those set forth by industry and government.
Read more
GM / Chevy / Cadillac (GMT800) Telescopic Trailer Tow Mirror Fitting Instructions
Made by the world’s largest manufacturer of exterior mirrors, the Telescopic Trailer Tow Mirror combines great looking aerodynamic styling with the toughness only a company like Schefenacker can produce. You’ve chosen one of the hottest new products in the past few years! Its interchangeable covers mean you can personalize the looks that suit you and your pick up, and a wide range of options mean you can have the right equipment for the right job.
Read more
2003 Toyota Tundra Gentex Comp/Temp Mirror Installation
Installation Preparation 1. Inspect electrochromic mirror for damage or defects. 2. Verify with parts list. 3. Place parts on a clean, padded surface. 4. If the vehicle is equipped with an antitheft radio, the security code must be recorded prior to disconnecting the battery cable. The code should be reentered after reconnecting the negative battery terminal. 5. Disconnect battery negative terminal from battery and isolate cable. 6. Remove driver’s side A-pillar garnish. OPTIONAL STEP 7. Remove lower dash panel. OPTIONAL STEP 8. Remove the driver’s cover side trim / fuse block cover. OPTIONAL STEP 9. Store all removed parts on a clean, padded surface. 10. Remove & discard original equipment (OEM) rearview mirror.
Read more
