70-2054 General Motors Amplifier Bypass Harness Instalation Instructions
RPO codes tell what options & accessories a vehicle has. RPO codes can be found in the glove box, on the trunk lid or hatch, or on the drivers side door jam near the latch. If you find the RPO code & it does not match one listed above for your particular vehicle, you should not use this harness.
Many factory amplifiers are now incorporating the crossovers for the tweeters and subwoofers within the amplifier. When bypassing the factory amplifier, you need to cross over those speakers with either passive crossovers or use an after-market AMP with built in crossovers.
Read more
Nissan 300ZX HKS Twin Power Ignition Amplifier Installation Guide
Most will say that the stock ignition system of the 300zx is sufficient unless you are running extreme levels of boost.
However there are others that say that they get increased throttle response and a slight performance gain from this modification.
Read more
1999 Mercedes Benz Truck ML 430 AR68.10-P-1000GH Remove/Install Instrument Panel
Removing And Installing Instrument Panel
Remove/Install
1 Remove instrument panel bottom section (1()
2 Remove A-pillar trim on left and right
3 Remove upper section of air outlet panel (1) Long wedge: See Special Tools below.
4 Unscrew screws (3) from upper side of instrument panel
5 Remove instrument cluster (A1 remove
6.1 Disconnect sun sensor connector
NOTE: Only as of 01.09.01: Connector is located behind instrument cluster
Read more
2008 Toyota Highlander w/Smart Key TVIP V4 Remove Engine Starter (RES)
1. Vehicle Disassembly. (a) Place the Vehicle in Park and have the Parking Brake Set before disconnecting the Battery. (b) Remove the Negative Battery Cable (Fig. 1-1) (1) Protect the Fender before starting. (2) Note the Battery Cable position, as it will be re- installed in the same position. CAUTION: Do not touch the positive terminal. (c) Remove the Glove Box Under Cover. (Fig. 1-3) (1) Begin by protecting the Vehicle Interior with Blankets. (d) Remove the Passenger’s Step Cover. (Fig. 1-4) (e) Remove the Passenger’s Cowl Cover. (Fig. 1-5) (1) Remove 1 Nut. (f) Remove 2 Bolts from the Glove Box, then open the Glove Box Door. (Fig. 1-6) (g) Remove 3 Screws from the Glove Box. (Fig. 1-7) CAUTION: Sharp Metal Edges. (h) Dislodge the Glove Box. (Fig. 1-7) (i) Disconnect all Connectors from the Glove Box. (Fig. 1-8) (j) Remove the Cable Clamp from the Glove Box. (Fig. 1-8)
Read more
1992 Dodge Colt Remove/Install/Overhaul
Removal, overhaul and installation procedures are covered in this article. If component removal and installation is primarily an unbolt and bolt-on procedure, only a torque specification may be furnished.
FUEL PUMP
Removal & Installation
1) Fuel pump assembly is located inside fuel tank. Release fuel pressure. See FUEL SYSTEM PRESSURE RELEASE. Raise vehicle on hoist. Drain fuel into suitable container. Disconnect electrical connectors and fuel hoses at fuel tank.
2) Remove fuel filler hose from fuel tank. Remove nuts securing fuel tank. Remove fuel tank from vehicle, and remove fuel pump assembly. To install, reverse removal procedure. Tighten nuts to specification. See TORQUE SPECIFICATIONS table at end of article.
Read more
1998 Mercedes Benz SLK 230 L4-2.3L SC Rear Center Console Remove/Install
Removing And Installing Rear Center Console
Removing And Installing Front Center Console
AR68.20-P-2350G Remove/Install Cover on Center Console
Removing And Installing Cover On Center Console
Read more
1995 Cadillac Concours N-Remove/Install/Overhaul
Removal, overhaul and installation procedures (when given by manufacturer) are covered in this article. If component removal and installation is primarily an unbolt and bolt-on procedure, only a simple torque specification may be supplied.
IGNITION SYSTEM POWERTRAIN CONTROL MODULE (PCM)
CAUTION: Electronic components used in control systems are designed to carry very low voltages. As little as a 30-volt charge created by static electricity can cause a total or degrading failure in PCM or other electronic components containing integrated circuits. Before servicing PCM, ground yourself and ground work area to discharge stored electricity.
Read more
Heated Windshield Washer Module Short Circuit Permanently Disable and Remove Module
General Motors has decided that a defect, which relates to motor vehicle safety, exists in certain 2006-2009 model year Buick Lucerne; Cadillac DTS; HUMMER H2; 2008-2009 model year Buick Enclave; Cadillac CTS; 2007-2009 model year Cadillac Escalade, Escalade ESV, Escalade EXT; Chevrolet Avalanche, Silverado, Suburban, Tahoe; GMC Acadia, Sierra, Yukon, Yukon XL; Saturn OUTLOOK; and 2009 model year Chevrolet Traverse vehicles equipped with a heated washer fluid system (RPO XA7/CHW). A recall was implemented on some vehicles in 2008 to add a fuse to the HWFS control circuit Read more
2001 Mercedes Benz E 320 Sedan V6-3.2L Door Liner on Rear Door Remove/Install
Removing/Installing
1. Press of handle recess (3) using assembly wedge
2. Unscrew screw (4) in the area of the interior door control
3. Unclip cover (11) and unscrew screw (12) With code 293 (rear side airbag)
4. Unscrew screw (1) on lock escutcheon (2) and remove lock escutcheon (2) downwards
5. Press of cover (5) under armrest and unscrew screw (6)
Read more
BMW E46 Subwoofer System by BSW Installation Guide: d110.e46c for BMW 3 Series
We’re going to proceed as follows:
1. Disassembling the trunk
2. Power/ground wire connections
3. Making appropriate wiring connections for audio inputs
4. Installing the subwoofer enclosure
5. Tuning/testing the system
Read more
