2000-2001 Audi TT 1.8L Turbo Short Throw Shifter Installation Instructions
This B&M Short Throw Shifter has been designed to work on most 2000-2001 Audi TT 1.8L Turbo models. It has been engineered to greatly reduce shift throw and improve shifter feel. The B&M Short Throw Shifter has been designed to work with the stock knob as well as the B&M Knob. Check the parts and tools lists at the beginning of these instructions for the supplied parts and the tools required to install your B&M Short Throw Shifter. Installation of the B&M Short Throw Shifter can be accomplished by anyone with minimal mechanical experience.
Read more
2001 Mercedes Benz E 320 Sedan V6-3.2L Door Liner on Rear Door Remove/Install
Removing/Installing
1. Press of handle recess (3) using assembly wedge
2. Unscrew screw (4) in the area of the interior door control
3. Unclip cover (11) and unscrew screw (12) With code 293 (rear side airbag)
4. Unscrew screw (1) on lock escutcheon (2) and remove lock escutcheon (2) downwards
5. Press of cover (5) under armrest and unscrew screw (6)
Read more
2001-2005 Ford Taurus Camshaft Tick Noise—3.0L 4V Engine
This article supersedes TSB 04-20-8 to update the vehicle model years and Service Procedure. ISSUE Some 2001-2005 Taurus/Sable, 2001-2006 Escape and 2005-2006 Mariner vehicles built prior to 1-17-2006 equipped with the 3.0L 4V Duratec engine may exhibit a ticking noise from the left bank cylinder head, with the engine at normal operating temperature only.
Read more
1999.5-2001 Audi A4 (B5) HID conversion installation instructions
1. Take the kit out of the box and lay everything out. You can install either the ballasts or bulbs first but typically it is easier to install the bulbs first.
2. There are 3 T27 torx screws holding the headlight on. The 2 on top are visible in this picture.
3. with the 2 screws removed.
4. The third screw is shown here. A long extension is needed to get to it and an extendable magnet is helpful to retrieve the screw (or bit if it falls).
5. Disconnect the headlight and turn signal connectors and remove the headlight by pulling it toward the outside of the car and toward you.
Read more
2001-2004 Audi A6 4B C5 Single-Frame front bumper HF 7551 Installation Guide
1. Removal of the original bumper:
Remove all screws which hold the bumper. Also remove the screws which hold the alloy bar and remove the bumper with the alloy bar. Remove the alloy bar from the bumper and install it into the new Hofele-Design bumper.
2. Placement of the Hofele-Design front bumper on the car:
Place the new bumper on the car but do not yet bolt it on.
3. Preparation of the bonnet:
Remove the front grill and the rubber strap behind it. Install the front grill (HF 7052-S4 / RS4) in the extension piece.
Read more
2008 Toyota Highlander w/Smart Key TVIP V4 Remove Engine Starter (RES)
1. Vehicle Disassembly. (a) Place the Vehicle in Park and have the Parking Brake Set before disconnecting the Battery. (b) Remove the Negative Battery Cable (Fig. 1-1) (1) Protect the Fender before starting. (2) Note the Battery Cable position, as it will be re- installed in the same position. CAUTION: Do not touch the positive terminal. (c) Remove the Glove Box Under Cover. (Fig. 1-3) (1) Begin by protecting the Vehicle Interior with Blankets. (d) Remove the Passenger’s Step Cover. (Fig. 1-4) (e) Remove the Passenger’s Cowl Cover. (Fig. 1-5) (1) Remove 1 Nut. (f) Remove 2 Bolts from the Glove Box, then open the Glove Box Door. (Fig. 1-6) (g) Remove 3 Screws from the Glove Box. (Fig. 1-7) CAUTION: Sharp Metal Edges. (h) Dislodge the Glove Box. (Fig. 1-7) (i) Disconnect all Connectors from the Glove Box. (Fig. 1-8) (j) Remove the Cable Clamp from the Glove Box. (Fig. 1-8)
Read more
2001 Lexus GS 300 L6-3.0L (2JZ-GE) – Blower Motor Assembly
REMOVAL
1. REMOVE No.2 UNDER COVER
2. REMOVE BLOWER MOTOR
a. Disconnect the connector.
b. Remove the 3 screws and blower motor.
Read more
1996-2001 Audi A4 B5 Panzer Plate Skid Plate Installation Instructions
First-time Install Procedure:
Raise car in the air: Use either ramps and wheel chocks or a jack and a pair of jack stands, or a car lift. Car must be raised on both sides for procedure to work.
Remove old belly pan:
1. Put on safety goggles. Remove old plastic belly pan if you still have one installed on your car. Save all 1/4 turn Dzus screws, if present, in provided zip-loc bag. You will not need these for the install but it’s nice to have spares.
2. Remove rear mount of belly pan, if present, with a 10mm wrench (the one with three receptacles on it.). Remove all three 1/4 turn screw (Dzus) receptacles, if present, and save them as spares in provided zip-loc bag. You might want to degrease them first
Read more
1992 Dodge Colt Remove/Install/Overhaul
Removal, overhaul and installation procedures are covered in this article. If component removal and installation is primarily an unbolt and bolt-on procedure, only a torque specification may be furnished.
FUEL PUMP
Removal & Installation
1) Fuel pump assembly is located inside fuel tank. Release fuel pressure. See FUEL SYSTEM PRESSURE RELEASE. Raise vehicle on hoist. Drain fuel into suitable container. Disconnect electrical connectors and fuel hoses at fuel tank.
2) Remove fuel filler hose from fuel tank. Remove nuts securing fuel tank. Remove fuel tank from vehicle, and remove fuel pump assembly. To install, reverse removal procedure. Tighten nuts to specification. See TORQUE SPECIFICATIONS table at end of article.
Read more
2000-2001 Audi TT Coupe Compact Disc Changer Installation Instructions
The following pages contain CD Changer installation instructions for the model listed above.
Rear seat, removal
– Remove rear seat bottom.
– Disconnect left rear seat belt at body anchorage point.
– Remove left rear seat back.
– Disconnect left front seat belt body anchor at floor (located at rear of front seat).
Read more
