2007-2008 BMW E82/88 135i Intake kit Installation Instructions
Step 1: Complete Stock Intake.
Step 2: Disconnect vacuum line and pull back.
Step 3: Unclip upper half of air box to remove lid and filter.
Step 4: Pull back rubber mount attached to battery cable. Use pliers if necessary. This will allow stock clamp to be loosened. (To be done in step 5B.)
Step 5: A) Loosen clamp closest to the radiator with 1/4” nut driver. B) Loosen clamp closest to fire wall with 1/4” nut driver. Leave clamps in position.
Read more
2008 HARTGE BMW 135i Coupe
HARTGE has given the world’s first inline six-cylinder engine with twin turbo-chargers and a second generation direct-injection system a power boast of 44 hp – and that at the same time as maintaining its extremely good fuel consumption of only 9.2 litres per 100 kilometres (EU combined). HARTGE not only offers an additional ECU, which transforms the 3-litre engine of the compact BMW 135i Coupé into a powerhouse generating a massive 257 kW (350 hp) at 5660 rpm and 480 Nm (lb-ft 354) at 2950 rpm, and naturally also the chance to enjoy unlimited driving pleasure at speeds of up to 280 km/h. For the dash from 0 to 100 km/h (0 – 62 mph), the 135i Coupé from HARTGE is half a second faster than its standard brother while the 25 mm lower sports suspension guarantees safety thanks to even greater directional stability and outstanding handling on twisting roads.
Read more
Volkswagen Touareq Fuel Filter Replacing (Diesel Engine)
There are two different fuel filter systems in Touareq. In system 1, the fuel filter is located on the engine, under the engine cover. In system 2, the fuel filter is located to the left in the engine compartment, on the strut tower. Special tools, testers and auxiliary items required Remove engine cover Upper engine cover, removing and installing .
Read more
2006 Audi A3 2.0FSI/VW MK5 Golf Carbonio Intake System Installation Instructions
Please take the time to fully read over these instructions before attempting to install the kit. This will greatly speed up the installation process and minimize any difficulties you may encounter.
Tools Required:
- Large opening pliers
- Torx T-20 socket tip
- Ratchet with extensions
- Flat head screwdriver
- Phillips head screwdriver
Read more
2004+ Subaru Legacy GT & Outback XT Power Filter Installation Instructions
You are now the proud owner of a highly tested and proven AVOTurboworld Power Air intake kit. While you have made a wise choice in selecting this suspension part, below we have some suggestions and procedures for you to follow to ensure a successful installation. The AVO Power Air intake kit is modular and can either be fitted as a complete kit, or as individual parts. The following instructions are a step-by-step guide for a complete installation – you can skip to the relevant section if you are only installing part of the kit.
Tools Required 10mm and 12mm socket and ratchet Flathead screwdriver Philips head screwdriver Bull nose pliers Kitting List
Read more
1999 Mercedes Benz Truck ML 430 AR68.10-P-1000GH Remove/Install Instrument Panel
Removing And Installing Instrument Panel
Remove/Install
1 Remove instrument panel bottom section (1()
2 Remove A-pillar trim on left and right
3 Remove upper section of air outlet panel (1) Long wedge: See Special Tools below.
4 Unscrew screws (3) from upper side of instrument panel
5 Remove instrument cluster (A1 remove
6.1 Disconnect sun sensor connector
NOTE: Only as of 01.09.01: Connector is located behind instrument cluster
Read more
2008 Toyota Highlander w/Smart Key TVIP V4 Remove Engine Starter (RES)
1. Vehicle Disassembly. (a) Place the Vehicle in Park and have the Parking Brake Set before disconnecting the Battery. (b) Remove the Negative Battery Cable (Fig. 1-1) (1) Protect the Fender before starting. (2) Note the Battery Cable position, as it will be re- installed in the same position. CAUTION: Do not touch the positive terminal. (c) Remove the Glove Box Under Cover. (Fig. 1-3) (1) Begin by protecting the Vehicle Interior with Blankets. (d) Remove the Passenger’s Step Cover. (Fig. 1-4) (e) Remove the Passenger’s Cowl Cover. (Fig. 1-5) (1) Remove 1 Nut. (f) Remove 2 Bolts from the Glove Box, then open the Glove Box Door. (Fig. 1-6) (g) Remove 3 Screws from the Glove Box. (Fig. 1-7) CAUTION: Sharp Metal Edges. (h) Dislodge the Glove Box. (Fig. 1-7) (i) Disconnect all Connectors from the Glove Box. (Fig. 1-8) (j) Remove the Cable Clamp from the Glove Box. (Fig. 1-8)
Read more
NewSouth Performance Mk5/EOS/B6 TurboPod kit Installation
This document outlines how to install a NewSouth Performance Mk5/EOS/B6 TurboPod kit1. Please review this document before attempting your installation.
INSTALLATION INSTRUCTIONS
Use appropriate safety precautions at all times. Make sure car in securely parked and on a level surface. Remove positive terminal of battery when working with electricity.
Read more
1992 Dodge Colt Remove/Install/Overhaul
Removal, overhaul and installation procedures are covered in this article. If component removal and installation is primarily an unbolt and bolt-on procedure, only a torque specification may be furnished.
FUEL PUMP
Removal & Installation
1) Fuel pump assembly is located inside fuel tank. Release fuel pressure. See FUEL SYSTEM PRESSURE RELEASE. Raise vehicle on hoist. Drain fuel into suitable container. Disconnect electrical connectors and fuel hoses at fuel tank.
2) Remove fuel filler hose from fuel tank. Remove nuts securing fuel tank. Remove fuel tank from vehicle, and remove fuel pump assembly. To install, reverse removal procedure. Tighten nuts to specification. See TORQUE SPECIFICATIONS table at end of article.
Read more
1998 Mercedes Benz SLK 230 L4-2.3L SC Rear Center Console Remove/Install
Removing And Installing Rear Center Console
Removing And Installing Front Center Console
AR68.20-P-2350G Remove/Install Cover on Center Console
Removing And Installing Cover On Center Console
Read more
