2001-2004 Audi A6 4B C5 Single-Frame front bumper HF 7551 Installation Guide
1. Removal of the original bumper:
Remove all screws which hold the bumper. Also remove the screws which hold the alloy bar and remove the bumper with the alloy bar. Remove the alloy bar from the bumper and install it into the new Hofele-Design bumper.
2. Placement of the Hofele-Design front bumper on the car:
Place the new bumper on the car but do not yet bolt it on.
3. Preparation of the bonnet:
Remove the front grill and the rubber strap behind it. Install the front grill (HF 7052-S4 / RS4) in the extension piece.
Read more
350Z GT Aero Front Bumper Installation Manual
This product is meant to fit Nissan 350Z only. Please check the parts before mounting.
- Mounting Procedure
Please follow the manufacturer’s repair manual for proper front bumper cover removal procedure.
（Remove the side bracket from the OEM bumper. ）
(Remove the impact foam from the front of the bumper.）
Install the side bracket onto the GT bumper by reversing the steps used to remove it.
Install the GT bumper using the factory clips and screws to the original locations.
Read more
Audi HomeLink System (Europe) with the transmitter unit in the front bumper
The HomeLink system provides a convenient way to replace up to three remote controls with a single built-in component. This innovative feature learns the radio frequency codes of most current remote controls used to activate garage doors, property gates, security systems, and home or office lighting.
Read more
2004-05 Chevy Colorado Prerunner Rear Bumper Installation
This kit should only be installed on a vehicle that is in good mechanical condition. Before installing the kit, replace worn or corroded parts. If the vehicle is suspected to have been in a collision or abused, DO NOT install the kit. The components in this kit do not eliminate weaknesses that may exist in the original equipment components.
Read more
Complementing the 987C Boxster S with the 987A Cayman S Front and Rear Bumper Covers
Why change the Boxster S Bumpers? You fall in love with a Porsche—and start improving, modifying, and changing it until it reflects who you are. It doesn’t matter what kind of perfection you’re chasing. Porsche geekdom is one religion with many denominations: club racing, driver’s education, autocrossing, rallying, touring, preservations, concours, and socialization. If you don’t change it and make it uniquely yours, then you’re not really a Porsche guy, just a temporary owner.
Read more
2002 Cadillac Escalade Front Bar Part #4049 A Installation Instructions
INSTALLING THE MOUTNING FRAME BRACKETS
1. Remove factory tow hooks from front section of vehicle
2. align driver side mounting bracket to the bottom and outer edge existing holes. Position bracket in manner shown below. See figure 1.1
3. attach mounting frame brackets using the 7/16 x 1 ― hex bolts, 7/16 hex nuts and 7/16 washers. (hand tighten as you may have to move the brackets around slightly, to align the front bar)
NOTE: (2WD MODELS YOU MAY HAVE TO CUT A SPACE IN THE PLASTIC SPOILER FOR THE BOTTOM OF THE FRONT BAR UP RIGHTS TO SLIDE THROUGH AND EVENTUALLLY ATTACH TO THE FRAME MOUNTING BRACKETS.
Read more
2002-05 Cadillac Escalade Front Bar Part # 4049 Installation Instructions
Installing the mounting frame brackets
1. Remove factory tow hooks from front section of vehicle
2. Align driver side mounting bracket to the bottom and outer edge existing holes. Position bracket in manner shown below.
3. Attach mounting frame brackets using the 7/16 x 1 ― hex bolts, 7/16 hex nuts and 7/16 washers. (hand tighten as you may have to move the brackets around slightly, to align the front bar)
NOTE: 2WD models, you may have to cut a space in the plastic spoiler for the bottom of the front bar up rights to slide through and eventually attach to the frame mounting brackets.
Read more
2002-2007 Subaru Impreza WRX/STI Front Mount Intercooler
1) Raise hood and disconnect battery.
2) Remove existing intercooler by removing (2) 12mm bolts, and (2) hose clamps. Remove Throttle Body Coupler. (1) hose clamp.
3) Remove intercooler support brackets, (2) 12mm bolts on drivers side bracket, and (2) 12mm bolts on passenger side bracket.
4) Remove intake system up to turbo inlet hose. This includes removing the rubber intake elbow (2 hose clamps), filter box (2 12mm bolt located on chassis), and resonator box (2 10mm nuts). Resonator box can be better reached when bumper is removed.
5) Remove coolant overflow tank (either 2 10mm bolts, or one clip) from radiator & drain into suitable container. NOTE: Coolant will be reused later.
Read more
Land Rover Series II HA and III Front Recovery Capstan Winch Fitting Instructions
1. Di scard front apron panel Mark and drill one hole.
2. Position riv-nut in crossmember and expand.
3. Fit support plate with one bolt.Mark and drill remaining 9 holes.
4. Fit 4 other riv-nuts to crossmember.
5. From beneath the vehicle cut out radiator cowl.
6. Fit new starter dog to engine
7. Secure support plate and rope guide brackets to bumper and crossmember. Fit Winch to support plate.
8. Apply grease, insert spring assemble drive shaft, and engage with crank dog
Read more
2004 Toyota Camry L4-2.4L Front Brake System
This document cover the installation of front brake for Toyota Camry:
OVERHAUL HINT: Overhaul the RH side by the same procedures with LH side.
1. REMOVE FRONT WHEEL
2. DRAIN BRAKE FLUID NOTICE: Wash off the brake fluid immediately if it comes into contact with a painted surface.
3. DISCONNECT FRONT FLEXIBLE HOSE
a. Remove the union bolt and a gasket from the disc brake cylinder, then disconnect the flexible hose from the disc brake cylinder.
4. REMOVE DISC BRAKE CYLINDER ASSY FR LH
a. Remove the 2 bolts and disc brake cylinder.
5. REMOVE DISC BRAKE PAD KIT FRONT (PAD ONLY)
a. Remove the 2 brake pads with anti-squeal shim.
Read more
