2003 Subaru Outback Wiper & Washer Systems
2003 ACCESSORIES & EQUIPMENT Wiper & Washer Systems – Baja, Legacy & Outback REAR WIPER ARM
Removal 1. Raise wiper arm cover (A). 2. Loosen nut to remove wiper arm.
INSTALLATION 1. Install in the reverse order of removal. 2. Operate rear wiper once. 3. Align blade to rear defogger heat wire (A).
Tightening torque: Refer to FRONT WIPER , COMPONENT, General Description.
Read more
2001-2004 Subaru Outback Skid Plate Installation Instructions
REMOVAL OF ORIGINAL SPLASH PAN Raise and safely support the vehicle on jack stands or on ramps. Locate and remove the two 12mm bolts at the rear of the factory splash pan. Locate and remove the two 10mm screws from the left and right side of the factory splash pan. These are located up inside the fender. Locate and remove the three remaining 12mm bolts from the front of the factory splash pan. The splash pan has retaining tabs around the three bolt holes from the last step and will require some downward force to remove the splash pan from the vehicle
Read more
2001 Lexus GS 300 L6-3.0L (2JZ-GE) – Blower Motor Assembly
REMOVAL
1. REMOVE No.2 UNDER COVER
2. REMOVE BLOWER MOTOR
a. Disconnect the connector.
b. Remove the 3 screws and blower motor.
Read more
Subaru 2.5L Turbo User Guide
Congratulations on the purchase of the new AccessPORT handheld programmer. The AccessPORT can: ● Reprogram the factory engine control unit (ECU) with improved tuning parameters through the on-board diagnostic (OBD-II) port ● Monitor vehicle sensor data using on-screen analog or digital gauges ● Read and clear engine diagnostic trouble codes (DTCs) ● Measure 0-60 and ¼ mile times* ● Monitor current and averaged fuel economy* ● Calculate current estimated horsepower and torque*
Supported Vehicle List ● 2004 – 2006 Subaru Impreza STI** ● 2005 – 2006 Subaru Legacy GT (MT & AT)** ● 2005 – 2006 Subaru Outback XT (MT & AT)** ● 2004 – 2006 Subaru Forester XT (MT & AT)** ● 2006 Subaru Impreza WRX (MT & AT)**
Read more
2001-2004 Ford Taurus Water In The Blower Case—Blower Motor
Inspect and seal cowl area and install Rain-Hat Extension Seal. Inspect and replace blower motor and/or blower motor resistor if there is evidence of water/corrosion. Refer to the following Service.
Procedure for details.
SERVICE PROCEDURE
1. Access blower motor and resistor per the Workshop Manual Sections 412-02 and 412-04. Inspect for evidence of water/corrosion. If water/corrosion are found or parts have failed, replace per Workshop Manual (blower motor 1F1Z-19805-AA and resistor F6DZ-19A706-AA).
Read more
1997 Subaru Legacy Car Security Wiring Diagram
Whether your an expert Subaru Legacy car alarm installer, Subaru Legacy performance fan or a novice Subaru Legacy enthusiast with a 1997 Subaru Legacy , a Subaru Legacy car alarm wiring diagram can save yourself a lot of time. One Subaru Car Alarm Wire Diagrams of the most time consuming tasks with installing an after market car alarm, car security, car remote start, automatic remote starter, shock sensor, tilt sensor, car alarm sensor or any auto alarm is identifying the correct color car security Rochester Auto Search wires for a 1997 Subaru Legacy. The Modified Life staff has taken all its Subaru Legacy car alarm wiring diagrams, Subaru Legacy car security wiring diagrams, Subaru Legacy car alarm wire diagrams, Subaru Legacy car security wiring schematics, Subaru Legacy car security diagrams, Subaru Legacy remote Read more
2001 GMC Truck C 1500 Truck 2WD Front Side Door Window Regulator Motor Replacement
Removal Procedure
1. Raise the window. If the window motor is inoperable, remove the window to gain access to the window motor retaining screws. Refer to Front Side Door Window Replacement.
2. Remove the power window module.
3. With the window regulator on the bench, remove fasteners one (1) and two (2) which will disconnect the drive housing and motor (4) from the rail (5) motor slides out of the gear/spool, hold the gear/spool into the housing with your fingers. The spool will unwind if it comes out of the housing.
4. Holding the motor and housing together, remove fastener three (3).
5. Slide the motor partially out of the gear/spool allowing finger access to the gear spool (6). Hold the gear/spool into the housing and remove the motor (7).
Read more
2001 Subaru Impreza 2.5 RS Coupe Timing Belt Service and Repair
INTERFERENCE ENGINE When installing the timing belt, be sure to align all alignment marks on the belt with corresponding marks on the sprokets. If incorrectly installed, interference between pistons and valves may occur. REMOVAL TIMING BELT 1. Remove timing belt guide. (MT vehicles only) 2. If alignment mark (a) and/or arrow mark (which indicates rotation direction) on timing belt fade away, put new marks before removing timing belt as shown in procedures below.
Read more
2005 Subaru Outback Limited Ignition (H4SO) Component (U5 Model)
Identifying Ignition (H4SO) Component (Except For U5 Model) CAUTION Wear work clothing, including a cap, protective goggles and protective shoes during operation. Remove contamination including dirt and corrosion before removal, installation or disassembly. Keep the disassembled parts in order and protect them from dust and dirt. Before removal, installation or disassembly, be sure to clarify the failure. Avoid unnecessary removal, installation, disassembly and replacement. Be careful not to burn yourself, because each part on the vehicle is hot after running. Be sure to tighten fasteners including bolts and nuts to the specified torque. Place shop jacks or rigid racks at the specified points. Before disconnecting electrical connectors of sensors or units, be sure to disconnect the ground cable
Read more
2004+ Subaru Legacy GT & Outback XT Power Filter Installation Instructions
You are now the proud owner of a highly tested and proven AVOTurboworld Power Air intake kit. While you have made a wise choice in selecting this suspension part, below we have some suggestions and procedures for you to follow to ensure a successful installation. The AVO Power Air intake kit is modular and can either be fitted as a complete kit, or as individual parts. The following instructions are a step-by-step guide for a complete installation – you can skip to the relevant section if you are only installing part of the kit.
Tools Required 10mm and 12mm socket and ratchet Flathead screwdriver Philips head screwdriver Bull nose pliers Kitting List
Read more
