Ford Escort IV 3/5 Doors Towing Hitch Fitting Instructions
This towing hitch is designed to assembly in following cars: FORD ESCORT IV 3/5 doors, produced since 01.1996 till 1998, catalogue no. C10 and is prepared to tow trailers max total weight 1250 kg and max vertical load 50 kg.
1. It is not necessary to reassemble the bumepr.
2. Find original signed places inside the boot on the left and right side, then drill ø24mm.
3. Slide the sleeves L=50mm (pos. 5) and position the element (pos. 4).
Read more
1991-1996 Ford Escort Radio Replacement
STEP 1: The Ford radio is snapped into the vehicles dash. With the proper tool, known as Ford radio removal keys, the Ford radio can be pulled forward out of the dash. A clothes hanger can be used instead of actual Ford radio removal keys. Cut the clothes hanger and bend 2 pieces in the shape as shown in the photos above. For more information on how to remove the radio, see the diagram below.
Read more
1992-2001 Ford Escort/ZX2 Short Throw Shifter Installation
This B&M Short Throw Shifter has been designed to work on most 1992 – 2001 Ford Escort/ZX2, 1992-1999 Mazda MX- 3/30X, 1992-1994 Mazda 323, and 1992-2002 Mazda Protegé/MP3/5 models. It has been engineered to greatly reduce shift throw and improve shifter feel. Check the parts and tools lists at the beginning of these instructions for the supplied parts and the tools required to install your B&M Short Throw Shifter. Installation of the B&M Short Throw Shifter can be accomplished by anyone with minimal mechanical experience.
Read more
1991-96 Ford Escort Baseplate BX2112 Installation Instructions
Installation of this baseplate requires removing the plastic belly pan. The brackets attached to the vehicle’s frame and the tie down brackets also need to be removed. They will be replaced with the baseplate’s side mounts. The plastic around the tie down brackets will need to be trimmed.
1. Read the General Instruction Sheet included with this baseplate.
2. Under the front corners of the car there is a stamped metal bracket that protrudes down with a slot at the bottom. These are called the tie down brackets. The baseplate mounts to the outside of the tie down brackets and to the center engine support bolts, using ten bolts, eight of which are supplied with the baseplate.
Read more
2001 Ford Escort ZX2 Timing Belt Service and Repair
Timing Drive Components-Timing Belt
NOTE: Ford does not provide camshaft gear timing marks, or information to perform timing belt service without the special tools shown in this procedure.
Removal
1. Grasp the spark plug boot firmly and with a twisting pulling motion, disconnect the spark plug wires from the spark plugs.
2. NOTE: If an original spark plug is reused, install it in the cylinder from which it was removed. New spark plugs can be used in any cylinder. NOTE: Use compressed air to remove any foreign material from the spark plug well before removing the spark plugs. Remove the spark plugs.
Read more
2002 Ford Escort ZX2 L4-2.0L DOHC VIN 3 Timing Belt Service and Repair
Timing Drive Components-Timing Adjust
NOTE:Ford does not provide camshaft gear timing marks, or information to perform timing belt service without the special tools shown in this procedure.
1. NOTE: Make sure the correct (second) notch in the pulley is indexed to the lower cylinder block. Position the crankshaft just prior to top dead center.
2. Remove the bolt and install the top dead center timing peg.
3. Rotate the crankshaft clockwise against the peg
Read more
Escort, Beltronics, and Valentine 1 Power Cords For Powered Mirrors
These cords will fit various models of the Whistler, Escort, Beltronics, AND the Valentine 1. Please check the initial installation chart below for your particular application. These are as reported back from prior customers. For more recent vehicle application guidelines and updates, Directions:
1) Pull the mirror around so that you can access the power plug in the back, or unplug the harness if it would seem to help.
2) Push the +12v pin connection (see chart above) into the back of the slot that is determined to the hot +12v on the mirror wiring harness.
Read more
1986-1990 Ford Escort Estate/Combi Van Towbars FD2266 Fitting Instructions
FITTING PROCEDURE
- Remove the spare wheel.
- Locate the two holes in rear chassis and drill up through the top skin at 11mm diameter. (Do not drill through the floor
– Remove the rear lights to access top of chassis). Open out the bottom holes just enough to accept spacer tubes (D) and use bolts (G) to fasten crossbar (B) in place with spacer tubes (D) in the chassis and the square washers (K) above the chassis.
- Fasten towbar (A) to crossbar (B) with bolts (H).
- Centralise the assembly and drill at 13mm diameter through centre hole into boot floor. Use bolt (F) to fasten crossbar (C) in place through Read more
02 Honda CR-V Creaking From A-Pillar When Turning Left
If owners of ’02 CR-Vs are complaining of a creaking from the A-pillar when turning left, the problem may be the right front engine mount on the cam chain side. If the rubber in the mount is misadjusted or faulty, it can make a creaking, ticking, or spot-weld-like noise that seems to be coming from the base of the front passenger’s A-pillar.
Read more
Powerlet PKT-044 BMW R1150GS Left “BEAK” Installation Instructions
This easy to install, high quality, POWERLET™ kit provides a convenient way to access the battery on BMW R1150GS motorcycles. The operator can supply power to the battery (i.e. battery charger), draw power from the battery (i.e. GPS), or monitor the state of charge on the battery using the Powerlet socket.
Read more
