2003-Up Nissan 350Z Edelbrock Nitrous System
The Edelbrock Nissan 350Z Performer EFI Nitrous System (Part Number 71007) is designed for 2003-Later Nissan 350Z vehicles equipped with stock 3.5L engines that utilize the returnless style fuel system. Horsepower and torque increases can vary with equipment upgrades and modifications.
Read more
Dirito Brothers’ Dealerships Step up to Support Nissan 350Z T2 Race Program
If you’ve been following this column, you’ll remember a very flattering article last month about the Mitsubishi EVO VIII MR, with an evaluation of its potential for racing action with the SCCA. Well, we’ve taken a step further into this racing discussion, and – this time – we got hooked. Last February, we began a discussion with Don Dirito of Dirito Brothers Nissan, VW, and Saab in Walnut Creek and Concord about the possibility of racing a Track model 350Z with support from their dealership. While we have a very high degree of respect for the EVO, when it comes to racing, there is just something about a traditional, normally aspirated, rear wheel drive two-seater sports car. And this appeal grew as we did more homework and discovered that the 350Z had shown well in the SCCA national racing program. Don Dirito was not familiar with SCCA racing.
Read more
350Z GT Aero Front Bumper Installation Manual
This product is meant to fit Nissan 350Z only. Please check the parts before mounting.
- Mounting Procedure
Please follow the manufacturer’s repair manual for proper front bumper cover removal procedure.
（Remove the side bracket from the OEM bumper. ）
(Remove the impact foam from the front of the bumper.）
Install the side bracket onto the GT bumper by reversing the steps used to remove it.
Install the GT bumper using the factory clips and screws to the original locations.
Read more
2003/2004 Nissan 350Z Turbocharger Systems Installation Instructions
Remove the turbocharger system from its carton and inspect for any obvious physical damage. All kit components are thoroughly inspected and carefully packaged prior to shipment from the factory. If any shipping damage is evident, contact your supplier and request that they process a claim with the shipper involved. Be sure to review the parts list on page 3 to verify that you have all necessary system components to proceed. If any components in the parts list are missing, contact Turbonetics’ customer service staff.
Read more
2003 Nissan 350z Tire Pressure Monitor System (TPMS) Warning Light Flashes Or Stays On
If the TPMS Warning Light (see Figure 1) flashes or stays ON, please use the “TPMS Diagnostic Chart” (page 2) to resolve the incident. NOTE: If more than one wheel transmitter is NOT activated, the blinking patterns for those wheels will combine. (Example: one blink/OFF/three blinks = LF and RR transmitters are not activated.)
CAUTION (for Pathfinder & Murano ONLY):
• Do NOT remove the Long Term Storage Fuse with the ignition key in the ON position.
• If the storage fuse is removed with the ignition key ON, the Wheel Transmitter (“Wake Up”) Activation procedure must be done.
Read more
2002-2005 Nissan 350Z Stillen Headers Installation Instructions
Installation:
1. Start install by raising vehicle to a suitable working height. Observe proper safety precautions when working under vehicle.
2. Disconnect negative terminal of battery. Remove the air inlet tube and airbox from the driver’s side of vehicle. On the passenger side move any brackets and/or harnesses that may interfere with access to the manifold bolts or heat shields.
3. Remove the lower splashguard from the vehicle. Remove the 4 nuts securing the ‘Y’ pipe to the back of the catalytic converters. Note: Nissan recommends that all locking nuts and gaskets be replaced after removal.
Read more
03-06 Nissan 350Z Oil Cooler Installation Instructions
1. Install the small rubber o-rings supplied with the kit onto all the fittings that screw into the oil outlet and inlet ports (threaded). Every connection to the oil filter sandwich block will require a rubber o-ring gasket. Do not use any thread sealer or Teflon tape on any of the fittings to the oil filter, block, cooler, or cooler lines. If you are installing an oil Read more
03-06 Nissan 350z Test pipes with Built in mechanical O2 sensor fix
Before you begin, allow engine to cool down. Spray down all bolts & nuts with WD-40 (or similar) and allow it to soak into the threads. The nuts & bolts will seize themselves onto the threads and spaying them down with Liquid Wrench or similar will make it much easier to remove the nuts & bolts.
- Test pipes laid out & test pipes laid out w/ additional wide band O2 ports.
- Close up detail of mechanical O2 sensor fix
- Remove 3 14mm nuts at exhaust manifold/catalytic converter flange. There are three nuts holding the catalytic converter to the exhaust manifold. Two nuts are facing the ground on one side of the flange, the third nut is on the opposite side of the flange. Use a 14mm stubby wrench or “S” wrench to remove the third nut. Repeat for other side.
Read more
2003-4 Nissan 350z Twin Turbo System Installlation Manual
This installation must only be performed by a competently trained technician possessing the factory manual for this vehicle and all of the tools and knowledge required to safely and successfully complete this specific work. This turbocharger kit has been engineered to provide the highest level of reliability achievable in an aftermarket upgrade and relies heavily on the ability of the installer to achieve this. If Jim Wolf Technology, Inc has not previously trained the installer on this installation, it is recommended that the qualified installer contact JWT before attempting this work.
Installation Steps – Perform the following preparatory work:
- Insure that the fuel tank is less than ― full and that it contains 91 or higher octane gas.
- Safely support the vehicle off the ground for easy access under the car.
- Disconnect the battery ground cable
Read more
2003 Nissan 350Z GReddy Turbo Kit (VQ35DE) Twin TD05-18G 8cm2
Factory Parts Removal
When removing the stock parts, make sure you read over the factory repair manual for proper procedures.
- Disconnect the negative terminal of the battery.
- Drain the engine oil, coolant and power steering fluid.
- Disconnect the air flow meter.
- Remove the Air cleaner assembly with airflow meter, intake tube, and breather hose.
- Remove the Top Radiator Hose and the Water Pipe (Located above the Right Exhaust manifold).
- Disconnect the primary and secondary O2 sensor and remove the exhaust manifold and catalytic converter.
- Remove the exhaust manifold.
Read more
