2008 Mercedes C-Class Estate New Design
Mercedes-Benz has fundamentally revised its brand identity for all communication materials with a new design. The new, standardised brand identity will be introduced in all corporate units – from Passenger Cars to Commercial Vehicles – and in all the world’s markets from November 1, 2007. It was developed on the basis of the brand’s history, and concludes the process of a more sharply focused brand positioning which began in 2006. The central theme of the new identity is the motto “The Star always shines from above”.
Read more
2001-2004 Audi A6 4B C5 Single-Frame front bumper HF 7551 Installation Guide
1. Removal of the original bumper:
Remove all screws which hold the bumper. Also remove the screws which hold the alloy bar and remove the bumper with the alloy bar. Remove the alloy bar from the bumper and install it into the new Hofele-Design bumper.
2. Placement of the Hofele-Design front bumper on the car:
Place the new bumper on the car but do not yet bolt it on.
3. Preparation of the bonnet:
Remove the front grill and the rubber strap behind it. Install the front grill (HF 7052-S4 / RS4) in the extension piece.
Read more
AD37 GM/Opel Pin Code Reader Operating Manual
The AD37 is a small portable device that can read the pin codes from GM/Opel vehicles typically up to year 2000 models. The system consists of an immobiliser which is an integral part of the antenna/coil that is mounted around the ignition barrel.
SYSTEM IDENTIFICATION As a general rule the pin code can be read from all models up to year 2000 vehicles fitted with a white resistor on the immobiliser electronic circuit board. To identify the correct system, the immobiliser unit has to be removed and inspected (Refer to page 7).
Read more
2006 Cadillac BLS
A design team led by GM Designer Chip Thole designed the new Cadillac BLS show car and the premium sedan is thus immediately recognizable as a member of the Cadillac family. “The most striking feature is the emphasis of the vertical lines on the front and rear,” says Thole. “The characteristic v-form of the chrome-plated grill is picked up again by the trunk lid. The large side faces communicate a sense of strength and solidity.” Nineteen-inch multi-spoke alloy wheels underline the impressive looks of the show car.
Read more
2009 Vorsteiner Porsche 911 V-GT
The 997 V-GT Coupe has been modified with all-new lightweight dry carbon fiber aerodynamic components from Vorsteiner.
• Full carbon fiber front bumper with integrated carbon fiber inlet ducting with upper radiator vent grill
• Replaceable carbon fiber front carbon chin spoiler attachment
• Rear vented bumper with integrated carbon fiber diffuser with aero fins
• Deck Lid/ Engine cover with integrated ram scoops & adjustable carbon fiber wing blade
• Carbon Fiber Door Sills with Vorsteiner Logo markings
Read more
2002 Chevy/GMC 3500-series Dual Underpro Speaker Installation Guide
This document provides all the necessary information to allow your Whelen product to be properly and safely installed. Before beginning the installation and/or operation of your new product, the installation technician and operator must read this manual completely. Important information is contained herein that could prevent serious injury or damage.
Read more
1953/54 Chevrolet RainGear Wiper System Installation Instructions
Pacific Western Design 53/54 Chevrolet Wiper System is designed to install in cars which are modified to use a 12- volt negative ground electrical system only and is not available for 6-volt(original)cars.
Read more
Cooling System V8 Datsun Z
A common problem with the V8 Datsun Z is overheating. In general, overheat due to insufficient air flow through the radiator, due to inefficient radiator designs. Some radiator designs restrict the air flow through the radiator. For example, a 4-row radiator is so thick, that an electric cooling fan cannot easily move air through a 4-row radiator. A 4-row radiator normally requires an engine-driven fan to draw air through the radiator.
Read more
Cadillac Escalade & EXT/ESV Liquid Grille 94215 Harley-Davidson Road King Instalation
A. Pre-installation Preparation
1. Verify kit contents.
2. Remove protective wrapping from inserts and place on a non-abrasive surface.
3. Remove the brackets and hardware from the box.
Read more
2002-2007 Subaru Impreza WRX/STI Front Mount Intercooler
1) Raise hood and disconnect battery.
2) Remove existing intercooler by removing (2) 12mm bolts, and (2) hose clamps. Remove Throttle Body Coupler. (1) hose clamp.
3) Remove intercooler support brackets, (2) 12mm bolts on drivers side bracket, and (2) 12mm bolts on passenger side bracket.
4) Remove intake system up to turbo inlet hose. This includes removing the rubber intake elbow (2 hose clamps), filter box (2 12mm bolt located on chassis), and resonator box (2 10mm nuts). Resonator box can be better reached when bumper is removed.
5) Remove coolant overflow tank (either 2 10mm bolts, or one clip) from radiator & drain into suitable container. NOTE: Coolant will be reused later.
Read more
