1999 Mercedes Benz Truck ML 430 AR68.10-P-1000GH Remove/Install Instrument Panel
Removing And Installing Instrument Panel
Remove/Install
1 Remove instrument panel bottom section (1()
2 Remove A-pillar trim on left and right
3 Remove upper section of air outlet panel (1) Long wedge: See Special Tools below.
4 Unscrew screws (3) from upper side of instrument panel
5 Remove instrument cluster (A1 remove
6.1 Disconnect sun sensor connector
NOTE: Only as of 01.09.01: Connector is located behind instrument cluster
Read more
1992 Dodge Colt Remove/Install/Overhaul
Removal, overhaul and installation procedures are covered in this article. If component removal and installation is primarily an unbolt and bolt-on procedure, only a torque specification may be furnished.
FUEL PUMP
Removal & Installation
1) Fuel pump assembly is located inside fuel tank. Release fuel pressure. See FUEL SYSTEM PRESSURE RELEASE. Raise vehicle on hoist. Drain fuel into suitable container. Disconnect electrical connectors and fuel hoses at fuel tank.
2) Remove fuel filler hose from fuel tank. Remove nuts securing fuel tank. Remove fuel tank from vehicle, and remove fuel pump assembly. To install, reverse removal procedure. Tighten nuts to specification. See TORQUE SPECIFICATIONS table at end of article.
Read more
1998 Mercedes Benz SLK 230 L4-2.3L SC Rear Center Console Remove/Install
Removing And Installing Rear Center Console
Removing And Installing Front Center Console
AR68.20-P-2350G Remove/Install Cover on Center Console
Removing And Installing Cover On Center Console
Read more
Heated Windshield Washer Module Short Circuit Permanently Disable and Remove Module
General Motors has decided that a defect, which relates to motor vehicle safety, exists in certain 2006-2009 model year Buick Lucerne; Cadillac DTS; HUMMER H2; 2008-2009 model year Buick Enclave; Cadillac CTS; 2007-2009 model year Cadillac Escalade, Escalade ESV, Escalade EXT; Chevrolet Avalanche, Silverado, Suburban, Tahoe; GMC Acadia, Sierra, Yukon, Yukon XL; Saturn OUTLOOK; and 2009 model year Chevrolet Traverse vehicles equipped with a heated washer fluid system (RPO XA7/CHW). A recall was implemented on some vehicles in 2008 to add a fuse to the HWFS control circuit Read more
Toyota Prius Case Study
There is a Toyota Prius Cab in Yellowknife operated by Kaad Mukhtaar, under City Cab LTD. This Case Study will look at his findings of how well the car functions as a Taxi, how well it performs in Yellowknife, the fuel efficiency of the vehicle, the cost avoided by purchasing a Prius compared to other taxi vehicles, and also the green house gases saved by driving a fuel efficient vehicle. The Toyota Prius is a Hybrid electric vehicle (HEV). A Hybrid electric vehicle combines a battery-powered electric motor with a conventional internal combustion engine. By combining electric power with internal combustion greater fuel efficiency can be achieved. The Energuide rating for the Toyota Prius for city driving is 4.0 L/100 km 1.
Read more
Toyota Wire Harness Repair Kit “B”
The new Wire Harness Repair Kit “B” has been released as an essential Special Service Tool (SST)
to supplement the original Wire Harness Repair Kit. This kit holds an initial supply of 21 new type
electrical terminals and connectors as well as the necessary supplies and small tools for most electrical repairs.
Read more
2004 Toyota Camry L4-2.4L Front Brake System
This document cover the installation of front brake for Toyota Camry:
OVERHAUL HINT: Overhaul the RH side by the same procedures with LH side.
1. REMOVE FRONT WHEEL
2. DRAIN BRAKE FLUID NOTICE: Wash off the brake fluid immediately if it comes into contact with a painted surface.
3. DISCONNECT FRONT FLEXIBLE HOSE
a. Remove the union bolt and a gasket from the disc brake cylinder, then disconnect the flexible hose from the disc brake cylinder.
4. REMOVE DISC BRAKE CYLINDER ASSY FR LH
a. Remove the 2 bolts and disc brake cylinder.
5. REMOVE DISC BRAKE PAD KIT FRONT (PAD ONLY)
a. Remove the 2 brake pads with anti-squeal shim.
Read more
1995 Cadillac Concours N-Remove/Install/Overhaul
Removal, overhaul and installation procedures (when given by manufacturer) are covered in this article. If component removal and installation is primarily an unbolt and bolt-on procedure, only a simple torque specification may be supplied.
IGNITION SYSTEM POWERTRAIN CONTROL MODULE (PCM)
CAUTION: Electronic components used in control systems are designed to carry very low voltages. As little as a 30-volt charge created by static electricity can cause a total or degrading failure in PCM or other electronic components containing integrated circuits. Before servicing PCM, ground yourself and ground work area to discharge stored electricity.
Read more
2007 Toyota Camry/Camry HV Interface Kit For iPod
Vehicle Disassembly (a) Set parking brake. (b) Remove the negative battery cable. (Fig. 1-1) (1) Protect the fender before starting. (2) Do not touch the positive terminal with any tool when removing cable. (c) Remove instrument panel garnish LH: (1) Disengage the 2 clips and remove the instrument panel garnish. (Fig. 1-2) NOTE: Pull the instrument panel garnish up at a 45º angle to remove it. (d) Remove instrument panel garnish RH: (1) Disengage the 2 clips and remove the instrument panel garnish. (Fig. 1-3) (e) Remove floor shift position indicator for automatic transmission. (1) Unscrew shift knob. (2) Disengage the 6 claws and 3 clips and remove assembly. (Fig. 1-4) (3) Disconnect any connectors. (f) Read more
1983-1986 Toyota Radio Wire Harnesses
Note: using an optional snap on wire harness adapter will simplify the wiring. Most snap on wire harness adapters have already converted and color coded the wires from the auto makers in dash wire harness to match typical aftermarket radio wire colors. ** The wire colors listed in the chart above are typical for these vehicles during these years but may not be the exact colors for this vehicle. This is another reason to use a snap on wire harness adapter. **
Read more
