2004-05 Chevy Colorado Prerunner Rear Bumper Installation
This kit should only be installed on a vehicle that is in good mechanical condition. Before installing the kit, replace worn or corroded parts. If the vehicle is suspected to have been in a collision or abused, DO NOT install the kit. The components in this kit do not eliminate weaknesses that may exist in the original equipment components.
Read more
1998 Mercedes Benz SLK 230 L4-2.3L SC Rear Center Console Remove/Install
Removing And Installing Rear Center Console
Removing And Installing Front Center Console
AR68.20-P-2350G Remove/Install Cover on Center Console
Removing And Installing Cover On Center Console
Read more
2001-2004 Audi A6 4B C5 Single-Frame front bumper HF 7551 Installation Guide
1. Removal of the original bumper:
Remove all screws which hold the bumper. Also remove the screws which hold the alloy bar and remove the bumper with the alloy bar. Remove the alloy bar from the bumper and install it into the new Hofele-Design bumper.
2. Placement of the Hofele-Design front bumper on the car:
Place the new bumper on the car but do not yet bolt it on.
3. Preparation of the bonnet:
Remove the front grill and the rubber strap behind it. Install the front grill (HF 7052-S4 / RS4) in the extension piece.
Read more
Complementing the 987C Boxster S with the 987A Cayman S Front and Rear Bumper Covers
Why change the Boxster S Bumpers? You fall in love with a Porsche—and start improving, modifying, and changing it until it reflects who you are. It doesn’t matter what kind of perfection you’re chasing. Porsche geekdom is one religion with many denominations: club racing, driver’s education, autocrossing, rallying, touring, preservations, concours, and socialization. If you don’t change it and make it uniquely yours, then you’re not really a Porsche guy, just a temporary owner.
Read more
350Z GT Aero Front Bumper Installation Manual
This product is meant to fit Nissan 350Z only. Please check the parts before mounting.
- Mounting Procedure
Please follow the manufacturer’s repair manual for proper front bumper cover removal procedure.
（Remove the side bracket from the OEM bumper. ）
(Remove the impact foam from the front of the bumper.）
Install the side bracket onto the GT bumper by reversing the steps used to remove it.
Install the GT bumper using the factory clips and screws to the original locations.
Read more
2001 Mercedes Benz E 320 Sedan V6-3.2L Door Liner on Rear Door Remove/Install
Removing/Installing
1. Press of handle recess (3) using assembly wedge
2. Unscrew screw (4) in the area of the interior door control
3. Unclip cover (11) and unscrew screw (12) With code 293 (rear side airbag)
4. Unscrew screw (1) on lock escutcheon (2) and remove lock escutcheon (2) downwards
5. Press of cover (5) under armrest and unscrew screw (6)
Read more
Audi HomeLink System (Europe) with the transmitter unit in the front bumper
The HomeLink system provides a convenient way to replace up to three remote controls with a single built-in component. This innovative feature learns the radio frequency codes of most current remote controls used to activate garage doors, property gates, security systems, and home or office lighting.
Read more
1999 Mercedes Benz Truck ML 430 AR68.10-P-1000GH Remove/Install Instrument Panel
Removing And Installing Instrument Panel
Remove/Install
1 Remove instrument panel bottom section (1()
2 Remove A-pillar trim on left and right
3 Remove upper section of air outlet panel (1) Long wedge: See Special Tools below.
4 Unscrew screws (3) from upper side of instrument panel
5 Remove instrument cluster (A1 remove
6.1 Disconnect sun sensor connector
NOTE: Only as of 01.09.01: Connector is located behind instrument cluster
Read more
2008 Toyota Highlander w/Smart Key TVIP V4 Remove Engine Starter (RES)
1. Vehicle Disassembly. (a) Place the Vehicle in Park and have the Parking Brake Set before disconnecting the Battery. (b) Remove the Negative Battery Cable (Fig. 1-1) (1) Protect the Fender before starting. (2) Note the Battery Cable position, as it will be re- installed in the same position. CAUTION: Do not touch the positive terminal. (c) Remove the Glove Box Under Cover. (Fig. 1-3) (1) Begin by protecting the Vehicle Interior with Blankets. (d) Remove the Passenger’s Step Cover. (Fig. 1-4) (e) Remove the Passenger’s Cowl Cover. (Fig. 1-5) (1) Remove 1 Nut. (f) Remove 2 Bolts from the Glove Box, then open the Glove Box Door. (Fig. 1-6) (g) Remove 3 Screws from the Glove Box. (Fig. 1-7) CAUTION: Sharp Metal Edges. (h) Dislodge the Glove Box. (Fig. 1-7) (i) Disconnect all Connectors from the Glove Box. (Fig. 1-8) (j) Remove the Cable Clamp from the Glove Box. (Fig. 1-8)
Read more
1992 Dodge Colt Remove/Install/Overhaul
Removal, overhaul and installation procedures are covered in this article. If component removal and installation is primarily an unbolt and bolt-on procedure, only a torque specification may be furnished.
FUEL PUMP
Removal & Installation
1) Fuel pump assembly is located inside fuel tank. Release fuel pressure. See FUEL SYSTEM PRESSURE RELEASE. Raise vehicle on hoist. Drain fuel into suitable container. Disconnect electrical connectors and fuel hoses at fuel tank.
2) Remove fuel filler hose from fuel tank. Remove nuts securing fuel tank. Remove fuel tank from vehicle, and remove fuel pump assembly. To install, reverse removal procedure. Tighten nuts to specification. See TORQUE SPECIFICATIONS table at end of article.
Read more
