2004-05 Chevy Colorado Prerunner Rear Bumper Installation
This kit should only be installed on a vehicle that is in good mechanical condition. Before installing the kit, replace worn or corroded parts. If the vehicle is suspected to have been in a collision or abused, DO NOT install the kit. The components in this kit do not eliminate weaknesses that may exist in the original equipment components.
Read more
2004-08 Chevy Colorado/Canyon 4WD Torsion Bar Leveling Kit
Installation steps for 2004-08 Chevy Colorado/Canyon Torsion Bar Leveling Kit
1. Place the vehicle on a level surface. Prior to beginning, record ride height on each side of the vehicle by measuring from the center of the spindle to a consistent point on the wheel well. Record these measurements for future reference.
2. Put the transmission in Park or 1st gear (manual transmissions) and chock the rear tires.
3. Raise the front of the vehicle using a jack. Raise it enough to completely unload the front suspension. Place a jack stand under each frame rail just behind the lower control arms for the front suspension. Ease the frame down on to the stands, but leave a slight load on the jack as a safety precaution.
Read more
2001-2004 Audi A6 4B C5 Single-Frame front bumper HF 7551 Installation Guide
1. Removal of the original bumper:
Remove all screws which hold the bumper. Also remove the screws which hold the alloy bar and remove the bumper with the alloy bar. Remove the alloy bar from the bumper and install it into the new Hofele-Design bumper.
2. Placement of the Hofele-Design front bumper on the car:
Place the new bumper on the car but do not yet bolt it on.
3. Preparation of the bonnet:
Remove the front grill and the rubber strap behind it. Install the front grill (HF 7052-S4 / RS4) in the extension piece.
Read more
350Z GT Aero Front Bumper Installation Manual
This product is meant to fit Nissan 350Z only. Please check the parts before mounting.
- Mounting Procedure
Please follow the manufacturer’s repair manual for proper front bumper cover removal procedure.
（Remove the side bracket from the OEM bumper. ）
(Remove the impact foam from the front of the bumper.）
Install the side bracket onto the GT bumper by reversing the steps used to remove it.
Install the GT bumper using the factory clips and screws to the original locations.
Read more
2004-2006 Chevy Colorado Brute Force Intake System Installation
Getting Started
a) Make sure vehicle is parked on a level surface. Set parking brake.
b) Disconnect negative battery terminal from the battery.
c) If engine has run within the past two hours, let it cool down.
Removal of the stock intake system.
a) Before removing any of the O.E. components, label each individual part so that no components become mixed up during the installation process.
Read more
Audi HomeLink System (Europe) with the transmitter unit in the front bumper
The HomeLink system provides a convenient way to replace up to three remote controls with a single built-in component. This innovative feature learns the radio frequency codes of most current remote controls used to activate garage doors, property gates, security systems, and home or office lighting.
Read more
Complementing the 987C Boxster S with the 987A Cayman S Front and Rear Bumper Covers
Why change the Boxster S Bumpers? You fall in love with a Porsche—and start improving, modifying, and changing it until it reflects who you are. It doesn’t matter what kind of perfection you’re chasing. Porsche geekdom is one religion with many denominations: club racing, driver’s education, autocrossing, rallying, touring, preservations, concours, and socialization. If you don’t change it and make it uniquely yours, then you’re not really a Porsche guy, just a temporary owner.
Read more
88-98 Chevy Truck Installation Instructions Kit #10002 #10003
Do not attempt to tow with the vehicle bumper after the relocating brackets have been installed. These brack- ets are designed to enhance the appearance of the vehicle. Towing with the bumper after the brackets have been installed could result in vehicle damage, personal injury or death. All towing should be done with a class III receiver hitch only. The manufacturer is not responsible for any damage or injury resulting from towing with the bumper.
Read more
2007 Chevy/GMC Tahoe/Yukon 2″ Front Leveling Kit Installation
Install Front Leveling Kit
1. Driver side coil-over
a. Scribe or paint coil-over with alignment mark for proper re-assembly.
b. Using spring compressors, carefully compress coil spring until coil spring is free from shock absorber.
c. Remove nut, upper plate, spring locator, and shock absorber from coil spring.
d. From CL220BAG: Install two kit dowel pins (3/ 16” x .875”) into kit spacer (lower)
e. Install kit spacer (lower) onto spring locator.
Read more
2007 Porsche Boxster S Removing Cover for Dashboard
Removing cover for center dashboard (defroster trim)
Installation Location: 1. Insert plastic wedge under dashboard cover (defroster trim) center -1- and lever out in upward direction – 2. Disconnect plug connection for sun sensor.
Read more
