2007-2008 BMW E82/88 135i Intake kit Installation Instructions
Step 1: Complete Stock Intake.
Step 2: Disconnect vacuum line and pull back.
Step 3: Unclip upper half of air box to remove lid and filter.
Step 4: Pull back rubber mount attached to battery cable. Use pliers if necessary. This will allow stock clamp to be loosened. (To be done in step 5B.)
Step 5: A) Loosen clamp closest to the radiator with 1/4” nut driver. B) Loosen clamp closest to fire wall with 1/4” nut driver. Leave clamps in position.
Read more
NewSouth Performance Mk5/EOS/B6 TurboPod kit Installation
This document outlines how to install a NewSouth Performance Mk5/EOS/B6 TurboPod kit1. Please review this document before attempting your installation.
INSTALLATION INSTRUCTIONS
Use appropriate safety precautions at all times. Make sure car in securely parked and on a level surface. Remove positive terminal of battery when working with electricity.
Read more
2006 Audi A3 2.0FSI/VW MK5 Golf Carbonio Intake System Installation Instructions
Please take the time to fully read over these instructions before attempting to install the kit. This will greatly speed up the installation process and minimize any difficulties you may encounter.
Tools Required:
- Large opening pliers
- Torx T-20 socket tip
- Ratchet with extensions
- Flat head screwdriver
- Phillips head screwdriver
Read more
2005-06 Chrysler 300C/Dodge Magnum & Charger 5.7L HEMI (MDS) Dual Rear Exit with Single Pro-Series 3.5” Tips
Factory Exhaust System Removal:
NOTE: Penetrating spray lubricant will assist with removal.
1. Loosen the nuts and bolts at the flange connection on the driver side of the tunnel muffler using a 13mm wrench or socket.
2. Remove the driver side factory hangers from the chassis using a 13mm socket and 12” extension attached to a 3/8” ratchet.
3. Remove the driver side axle pipe hanger from the grommet shown in Fig. D using grommet pullers or a similar device. Carefully remove the rear driver side section of the stock exhaust from the vehicle.
Read more
Chrysler, Dodge and Plymouth Transmission Mount Installation Instructions
Installation instructions:
1. Remove the bracket assembly from the vehicle.
2. Remove all of the old rubber from inside of the original shell before installing the New Energy Suspension bushings. If heat is used to remove the old rubber, you need to only heat the outer shell enough to loosen the bond of the old rubber. Do NOT burn out the bushing. Always use the proper protective/safety gear for the job and work in a well ventilated area.
Read more
2006 Chevrolet/GMC Duramax Upgrade Front Intercooler
Remove the heat exchanger from its carton and inspect for any obvious physical damage. All kit components are thoroughly inspected and carefully packaged prior to shipment from the factory. If any shipping damage is evident, contact your supplier and request that they process a claim with the shipper involved. Be sure to review the parts list on to verify that you have all necessary system components to proceed. If any components in the parts list are missing, contact Turbonetics’ customer service staff.
Read more
The Ultimate Dice Installation Manual For The 2007 BMW X3
Step 1: Remove the Armrest Tray
Open the top portion of the arm-rest and take out the rubber mat that is inside. It is secured by rubber stubs and will “snap” out when you pull on it. Next, take the T-15 Torx and remove the (4) screws that secure the upper armrest tray to the armrest assembly. Place the screws in a Zip Lock bag or other, secure area. Once you remove the tray, you will see the connectors for the BMW cell phone kit.
Do not touch or damage the cellular connections. You are now ready to move on to Step 2.
Read more
Honda Civic Si & Acura RSX Icebox Cold Air Intake Installation Instructions
Comptech Icebox Cold Air Intake for the 2002–2005 Honda Civic-Si and 2002–2005 Acura RSX. All components have been designed and manufactured utilizing the latest in technology and materials. Comptech recommends that you read through these instructions before starting installation and that you use an Acura Factory Shop Manual to supplement these instructions. All Comptech products are intended to be installed by a professional installer. Always use jack stands to support the vehicle when a car lift is not available. Always work in a clean environment and use the appropriate safety equipment to avoid any potential damage or injuries.
Read more
BMW Sirius Receiver Installation Guide For X5 (E53) with Navigation (MY03+)
This installation guide is intended to supplement the BMW Installation Instructions to help you with the installation of the BMW Sirius Receiver for X5 (E53) with Navigation. I opted for the Terk SIR3 Low-Profile Magnetic Mount antenna and mounted it in the spoiler. As a result, this guide will not cover the installation of the BMW Sirius Satellite Antenna and you should follow the instructions supplied with the BMW Sirius Satellite Antenna Kit if you decide to go that route. I found no signal loss or weak reception with the antenna being in the spoiler and would strongly recommend if you want to be stealth and do not like the obtrusive shape of the BMW Sirius antenna on your roof.
Read more
2005-06 Chevy Cobalt Exhaust System Installation
Exhaust System Removal:
1. Measure the exhaust pipe 7-1/2 inches forward of the rear axle and mark a line.
2. Using a saw or chain style pipe cutter, cut the stock system.
3. Using a 15 mm socket remove the two flange nuts.
4. Remove the front hanger from the rubber isolator and remove the front section of the stock exhaust system.
5. Remove the rubber isolator after the axle from both the vehicle and the exhaust system.
NOTE: Be sure to save all rubber isolators removed from the vehicle. They will be used to install the CORSA Performance exhaust system in later steps.
Read more
