2001-2004 Subaru Outback Skid Plate Installation Instructions
REMOVAL OF ORIGINAL SPLASH PAN Raise and safely support the vehicle on jack stands or on ramps. Locate and remove the two 12mm bolts at the rear of the factory splash pan. Locate and remove the two 10mm screws from the left and right side of the factory splash pan. These are located up inside the fender. Locate and remove the three remaining 12mm bolts from the front of the factory splash pan. The splash pan has retaining tabs around the three bolt holes from the last step and will require some downward force to remove the splash pan from the vehicle
Read more
Thor Audi A4 Skid Plate Installation Instructions
Now that you have familiarized yourself with the parts of the skid plate and prepared the tools you will need to do the job, you’re ready to get started.
Step #1: Drive your car onto a set of car ramps or jack the car up and place jack stands under the vehicle for safety. Also make sure to apply your emergency brake, (we recommend using both the ramps and the jack stands). Start by removing all of the plastic skid plates using your flat head screw driver. Also you will want to remove the metal bracket that is located just behind your lower sub frame. It is the black metal bracket that attaches to the frame with two 10mm head bolts. The following picture shows this bracket.
Some of the newer A4’s will have an extra plastic piece under your front fender liner that needs to be removed. It is held on with one Torx screw that is located directly in front of the tire in the fender well.
Read more
1996-2001 Audi A4 B5 Panzer Plate Skid Plate Installation Instructions
First-time Install Procedure:
Raise car in the air: Use either ramps and wheel chocks or a jack and a pair of jack stands, or a car lift. Car must be raised on both sides for procedure to work.
Remove old belly pan:
1. Put on safety goggles. Remove old plastic belly pan if you still have one installed on your car. Save all 1/4 turn Dzus screws, if present, in provided zip-loc bag. You will not need these for the install but it’s nice to have spares.
2. Remove rear mount of belly pan, if present, with a 10mm wrench (the one with three receptacles on it.). Remove all three 1/4 turn screw (Dzus) receptacles, if present, and save them as spares in provided zip-loc bag. You might want to degrease them first
Read more
Aluminum Rail Replacement on a 2004 and Newer 5 Series BMW
A 2004 BMW 5 Series BMW has been in an accident. The left rail has a golf ball size bend in it about 10 inches from the front end cap & the right rail is swayed out by 15 mm. Estimator A writes an estimate to pull the front end of the vehicle and repair both rails. Estimator B writes an estimate to pull the front end and replace the left rail.
Who is right? • Estimator A is only right • Estimator B is only right • Both Estimators are right • Both Estimators are wrong
The correct answer is D Both Estimators are wrong and the following presentation will explain why.
Read more
2009 Chevy Cobalt SS 2.0L 4 cyl. Turbo Dyno-Proven Intercooler Piping Installation
Before installing any parts of this system read the instructions thoroughly. If you have any questions regarding installation please contact the dealer you purchased this product from. Installation DOES require some mechanical skills. A qualified mechanic is always recommended. *Do not attempt to install the intake system while the engine is hot. The installation may require removal of radiator fluid line that may be hot.
Injen Technology offers a limited lifetime warranty to the original purchaser against defects in materials and workmanship.
Read more
1957 Cadillac Air Suspension – Part 1, The Front
After a number of years of engineering, Cadillac introduced air suspension on the 1957 Eldorado Brougham. For four years this option was offered, but since only 904 Broughams were built there were a very few equipped with air. In at least some years (if not all) from 1957 through 1960, Cadillac offered air suspension as a $215 option for both the Brougham and the non Brougham models. To do so, frames were built to accommodate both steel and air springs. Reports on these cars tell us that the system was quite remarkably smooth and comfortable (quite a complement considering Cadillac’s reputation for great ride) as long as they worked. The problem was that they were plagued with leaks. Leaks at fitting, and in controls, and anywhere else they could leak. They tended to freeze in the winter. You could lose air and drop the car without much warning. It was complicated and difficult to repair and maintain.
Read more
2007 Fiat Panda Aria Concept
The concept car combines an innovative powertrain architecture – represented by the new SGE 900 cc Turbo twin-cylinder engine, equipped with the Multiair® system for dual petrol/methane-hydrogen fuel management, MTA gearbox and Stop&Start device – with the adoption of eco-compatible materials (recycled, recyclable or of natural origin) both outside and inside. The interior is upholstered with natural fibres (cotton and linen), woven coconut fibre and biodegradable elements, while the exterior panelling is made of semi-transparent eco-resin and the structure is treated with opaque ‘totouch’ paint.
Read more
2006 Dodge Viper SRT10 Coupe
The exterior design of the all-new 2006 Dodge Viper SRT10 Coupe, with its “double-bubble” roof and dramatic, unique rear styling with wrap-around taillamps reminiscent of the Viper GTS Coupe, is what sets it apart from its Convertible sibling – and connects it to the Viper heritage.
“It was important for us to sustain the emotion in the design,” said Trevor Creed, Senior Vice President, Design, Chrysler Group. “We wanted the 2006 Dodge Viper SRT10 Coupe design to include a nod to the original Viper GTS Coupe, but in a contemporary way.
Read more
The Audi allroad quattro with additional shift stage Design and Function
After a 20 year history of four-wheel drive, Audi presents the allroad quattro. For the first time, a production model with off-road capability. The Audi allroad quattro is the synthesis of the classic estate and the traditional off-road vehicle. It combines the outstanding driving dynamics of the Audi A6 with the off-road capability of a four-wheel drive. Featuring the proven quattro drive, the improved running gear with ”4-level air suspension”, the optional ”low range” additional shift stage and the changes to the bodywork and the interior, the Audi allroad quattro combines two previously separate vehicle categories thereby offering ”the best of both worlds”. The Audi allroad quattro is the embodiment of a new vehicle category, the so-called “allroader”.
Read more
2008 BMW 3 Series Convertible
Fourth-generation 3 Series Convertibles featuring a first-for-BMW retractable hardtop with power operated three-piece steel roof for enhanced safety and outstanding vehicle dynamics – 335i Convertible equipped with a twin-turbocharged 3.0-liter inline 6-cylinder engine with 300 hp & 300 lb-ft of torque and direct fuel injection. 328i Convertible powered by an aluminum/magnesium 3.0-liter, inline 6-cylinder engine featuring Valvetronic technology and rated at 230hp & 200 lb-ft of torque. Luxurious and roomy interior with seating for four and enhanced details.
Read more
