2001-2004 Subaru Outback Skid Plate Installation Instructions
REMOVAL OF ORIGINAL SPLASH PAN Raise and safely support the vehicle on jack stands or on ramps. Locate and remove the two 12mm bolts at the rear of the factory splash pan. Locate and remove the two 10mm screws from the left and right side of the factory splash pan. These are located up inside the fender. Locate and remove the three remaining 12mm bolts from the front of the factory splash pan. The splash pan has retaining tabs around the three bolt holes from the last step and will require some downward force to remove the splash pan from the vehicle
Read more
1996-2001 Audi A4 B5 Panzer Plate Skid Plate Installation Instructions
First-time Install Procedure:
Raise car in the air: Use either ramps and wheel chocks or a jack and a pair of jack stands, or a car lift. Car must be raised on both sides for procedure to work.
Remove old belly pan:
1. Put on safety goggles. Remove old plastic belly pan if you still have one installed on your car. Save all 1/4 turn Dzus screws, if present, in provided zip-loc bag. You will not need these for the install but it’s nice to have spares.
2. Remove rear mount of belly pan, if present, with a 10mm wrench (the one with three receptacles on it.). Remove all three 1/4 turn screw (Dzus) receptacles, if present, and save them as spares in provided zip-loc bag. You might want to degrease them first
Read more
Thor Audi A4 Skid Plate Installation Instructions
Now that you have familiarized yourself with the parts of the skid plate and prepared the tools you will need to do the job, you’re ready to get started.
Step #1: Drive your car onto a set of car ramps or jack the car up and place jack stands under the vehicle for safety. Also make sure to apply your emergency brake, (we recommend using both the ramps and the jack stands). Start by removing all of the plastic skid plates using your flat head screw driver. Also you will want to remove the metal bracket that is located just behind your lower sub frame. It is the black metal bracket that attaches to the frame with two 10mm head bolts. The following picture shows this bracket.
Some of the newer A4’s will have an extra plastic piece under your front fender liner that needs to be removed. It is held on with one Torx screw that is located directly in front of the tire in the fender well.
Read more
No Holes License Plate Bracket Kit BMW Installation Instructions
This kit allows the owner of any BMW to attach a front license plate to their BMW without the need to drill holes. BMW has always attached the front license plate by drilling the front bumper and permanently mounting the plastic license plate bracket to the front bumper with screws. The ‘NO HOLES’ kit mounts the front license plate utilizing the front tow hook attachment point. The kit comes complete with all mounting hardware, including the screws to affix the license plate to the bracket. The bracket allows for the mounting of normal size US License plates, Rallye Plates and European style plates.
Read more
HP9606 Adapter Plate kit Chevy Engine
The Adapter Plate kit will allow you to use Buick, Pontiac or Oldsmobile and Cadillac 200, 350 and 400 Turbo-Hydramatic Transmissions with a Chevrolet engine. No alterations are necessary and installation is easy and simple.
NOTE: On some Turbo 400 transmissions, the webbing located inside the bell housing may interfere with two of the adapter plate kit bolts. Webbing must be trimmed to clear these bolts.
Read more
1998 Audi A6 Body Repairs
Vehicle identification data
Type plate and vehicle identification number
The type plate -A- is located at the rear bulkhead of the engine compartment behind the coolant reservoir.
Vehicles for certain export countries have no type plate.
The vehicle identification number -B- (chassis number) is stamped on the rear bulkhead in the engine compartment.
Vehicle data sticker
The vehicle data sticker is located in the spare wheel well at the rear of the vehicle.
Read more
1996-2000 Audi A4 Short Throw Shifter Installation Instructions
This B&M Short Throw Shifter has been designed to work on most 1996-2000 Audi A4, 2000 Audi S4, 2000 Audi A6, and 1996-2000 Volkswagen Passat models. It has been engineered to greatly reduce shift throw and improve shifter feel. Check the parts and tools lists at the beginning of these instructions for the supplied parts and the tools required to install your B&M Short Throw Shifter. Installation of the B&M Short Throw Shifter can be accomplished by anyone with minimal mechanical experience.
Read more
Audi A-2 Clamping Adapters Users Manual
The components of this clamping adapter system are used to anchor the Audi A-2 vehicle which has jack tubes and lift tabs in its rocker panels. The system provides a positive means of securing these vehicles to the EZ Liner mainframe.
IMPORTANT:
• Information on the use of anchoring stands
(including their attachment to the EZ Liner main-frame) appears in the Universal Anchoring Systems Owners Manual. (Part No. 618740.)
• Read all of these instructions prior to using the Audi A-2 Anchoring Accessory.
• Clean jack tubes using one of the anchoring pins. (See Figure 1.)
a. Insert a steel punch (or bar) through the 1/2 inch hole at end of pin and use it as a handle.
b. Rotate the pin right and left as it is moved in and out of the jack tube hole.
NOTE: Holes must be clean to allow for easy installation and removal of the anchoring assembly.
Read more
2002+ Audi A4 FWD/QUATTRO Street Sport Coil Over kit Installation
Before removing any parts, park the car on a secure, stable and level surface, loosen (but do not remove) the wheel lug nuts, jack the vehicle up and place the car on four stable jack stands or use a professional vehicle lift. We recommend having two people available for certain steps of the installation.
Front Install Instructions
1. Securely support both front corners of the car (relieving tension on the ARB).
2. Remove front wheels.
3. Remove Clip #1 using pliers. You do NOT need to reinsert this clip. Unfasten Nut #2, take out the hex bolt and pull both links upward and out.
Torque Spec: 40Nm.
4. Unscrew hex bolt (shock clevis) from suspension and control arm. Torque Spec: 90Nm with vehicle out or near ride height (use a transmission jack or floor jack)
5. From within the engine bay: Remove Cover to gain access to upper mount bolt.
6. Unscrew hex bolts #1 within engine bay. Take care not to damage the boot when remove bolts. Remove Front assembly from vehicle.
Read more
2003 Saturn L300 V6-3.0L VIN R P2119-Throttle Closed Position Performance
The throttle actuator control (TAC) module contains a direct current actuator motor
controlled by the ECM used to move the throttle plate (in either direction) and two throttle
position sensors to determine throttle plate position. The throttle plate is held at a 7% rest
position to a mechanical stop by a constant force return spring. This spring will hold the
throttle plate to the stop when there is no current flowing to the actuator motor. There is
another return spring, which creates constant force on the throttle plate only when the
throttle plate is moved towards the full closed position. The ECM will monitor both the
actuator motor and TP sensors for circuit faults, as well as check to make sure both
springs can return the throttle to the 7% position no matter where the throttle plate
remains.
Read more
