2002-2007 Subaru Impreza WRX/STI Front Mount Intercooler
1) Raise hood and disconnect battery.
2) Remove existing intercooler by removing (2) 12mm bolts, and (2) hose clamps. Remove Throttle Body Coupler. (1) hose clamp.
3) Remove intercooler support brackets, (2) 12mm bolts on drivers side bracket, and (2) 12mm bolts on passenger side bracket.
4) Remove intake system up to turbo inlet hose. This includes removing the rubber intake elbow (2 hose clamps), filter box (2 12mm bolt located on chassis), and resonator box (2 10mm nuts). Resonator box can be better reached when bumper is removed.
5) Remove coolant overflow tank (either 2 10mm bolts, or one clip) from radiator & drain into suitable container. NOTE: Coolant will be reused later.
Read more
Subaru Impreza ABS System Problem Technical Bulletin
This technical bulletin deals with common problems encountered on various manufacturers’ vehicles by the helpline staff over the last few months. These faults have been re -occurring during this time, and the following topics detail the faults and where possible the solutions to the problems.
Fault: ABS warning light constantly “ON” with no ABS operation. Callers often remark that they are unable to communicate with the ABS ECM even though using suitable diagnostic equipment.
Read more
Subaru Impreza Hatchback PN-140325 Exhaust System Installation
Borla Performance Cat-Back™ Exhaust System (Part Number 140325) has been designed for the Subaru Impreza Hatchback equipped with a 2.5L opposed 4 cylinder engine (non-turbo), all-wheel drive and automatic or manual transmissions.
Borla Performance Cat-Back Exhaust System Installation
1. Using the original hardware, place the front pipe assembly into position supporting it with a stand at the open end. Hand tighten the hardware for now. (See figure 3)
Read more
Subaru 2.5L Turbo User Guide
Congratulations on the purchase of the new AccessPORT handheld programmer. The AccessPORT can: ● Reprogram the factory engine control unit (ECU) with improved tuning parameters through the on-board diagnostic (OBD-II) port ● Monitor vehicle sensor data using on-screen analog or digital gauges ● Read and clear engine diagnostic trouble codes (DTCs) ● Measure 0-60 and ¼ mile times* ● Monitor current and averaged fuel economy* ● Calculate current estimated horsepower and torque*
Supported Vehicle List ● 2004 – 2006 Subaru Impreza STI** ● 2005 – 2006 Subaru Legacy GT (MT & AT)** ● 2005 – 2006 Subaru Outback XT (MT & AT)** ● 2004 – 2006 Subaru Forester XT (MT & AT)** ● 2006 Subaru Impreza WRX (MT & AT)**
Read more
2004+ Subaru Impreza WRX/STI Front Lip (polyurethane)
Polyurethane is a flexible material. Occasionally during shipping, sections of the lip may warp or bend in unusual shapes. DO NOT WORRY! Simply lay the lip flat and out in the sun for a day and it will return to its normal shape. To cure the waviness of the front portion, simply purchase a long metal or wood section, clamp this metal section inside the lip (clamps can be purchased at Home Depot), and lay out in the sun for about a day. This will fix the waviness problem.
Read more
Rally Armor Subaru Impreza WRX/STI/RS/2.5i – 2002-2007 Mud flap Mounting Instructions
Rally Armor recommends professional installation – Cautionary Note: The hardware is quite strong and self-threading but overtightening the clips is not recommended.
FRONT MUD FLAP installation:
Step 1: Remove the clips (1-4) and the two side skirt clips in the front to gain access to the body. Cautionary Note: Be careful not to rip the wheel well plastic. It tears easily. Pull back slowly!
Step 2: Pull the liner back and the side skirt down slightly.
Read more
1997 Subaru Legacy Car Security Wiring Diagram
Whether your an expert Subaru Legacy car alarm installer, Subaru Legacy performance fan or a novice Subaru Legacy enthusiast with a 1997 Subaru Legacy , a Subaru Legacy car alarm wiring diagram can save yourself a lot of time. One Subaru Car Alarm Wire Diagrams of the most time consuming tasks with installing an after market car alarm, car security, car remote start, automatic remote starter, shock sensor, tilt sensor, car alarm sensor or any auto alarm is identifying the correct color car security Rochester Auto Search wires for a 1997 Subaru Legacy. The Modified Life staff has taken all its Subaru Legacy car alarm wiring diagrams, Subaru Legacy car security wiring diagrams, Subaru Legacy car alarm wire diagrams, Subaru Legacy car security wiring schematics, Subaru Legacy car security diagrams, Subaru Legacy remote Read more
Genuine Subaru Performance Parts
A select group of performance and appearance parts to increase your driving pleasure. If you thought you couldn’t love your Subaru more, check out our line of Genuine Subaru Performance Parts to make your vehicle even more fun to own. Engineered specifically to enhance the performance, endurance and, in some cases, the look of your vehicle, these Genuine Subaru Performance Parts allow you to customize, without asking you to compromise the quality and integrity of your Subaru.
Read more
2001 Subaru Impreza 2.5 RS Coupe Timing Belt Service and Repair
INTERFERENCE ENGINE When installing the timing belt, be sure to align all alignment marks on the belt with corresponding marks on the sprokets. If incorrectly installed, interference between pistons and valves may occur. REMOVAL TIMING BELT 1. Remove timing belt guide. (MT vehicles only) 2. If alignment mark (a) and/or arrow mark (which indicates rotation direction) on timing belt fade away, put new marks before removing timing belt as shown in procedures below.
Read more
2005-06 HONDA CRV Grill/ Brush Guard Part #6049
Procedure installing the Grill to Honda CRV
1. Remove the plastic rivets securing the plastic guard located underneath the vehicle in order to install the front bar.
2. Start with the passenger side assembly, postion one of the 7/16 nut plates behind the cross member opening and align the 7/16 nut plate wit the two matching holes in the frame rail. Fasten the frame brackets to the bottom cross member as shown in the illustration using the 7/16 x 1 ¼ hex bolts, 7/16 washers, 5/16 self tapping bolt and 5/16 washers. Note: Do not over tighten 5/16 x 1 self tapping bolt as it might strip threads.
Read more
