Malfunction Indicator Lamp/Check Engine Light
If this indicator comes on while driving, there is a problem with your engine or its emission control systems. Even though you may feel no difference in your car’s performance, it can reduce your fuel economy and cause your car to put out excessive emissions. Continued operation may cause serious engine damage.
Read more
1999 Protege 1.6L Rattling Noise From Engine
APPLICABLE MODEL(S)/VINS
All 1999 Protege (1.6L) with VINs lower than JM1 BJ222* X0 140057.
All 1999 – 2000 Miata with (1.8L) VINs lower than JM1 NB353* Y0 155947.
DESCRIPTION A rattling noise may be heard from the engine when depressing the clutch or when revving the engine in neutral. In extreme cases, customers may experience noise at all times. This concern can be caused by improperly machined number 4 main cap of cylinder blocks which may result in premature wear of the thrust bearing. Customers having this concern should have their vehicle repaired using the following procedure.
Read more
1982 Mercedes Benz 240D (123 Chassis) Engine Oil Pan Service
Removal 1 Drain engine oil. 2 Lift engine hood to 90°position and lock left-hand latch (arrow). 3 On engine 617, remove adapter at air cleaner (arrow). On models with oil bath air cleaners, release and remove rubber gaiter from throttle body. 4 If model features uprated engine, also remove longitudinal control spindle. Unhook control rods for this purpose. Withdraw retainer (arrow) and force longitudinal control spindle in aft direction. 5 Unscrew clip attaching oil dipstick guide tube to power steering pump bracket and crankcase. 6 On models with power steering, Read more
2006 Civic Immobilizer Indicator Is Blinking, Engine Won’t Start
The engine does not start, and the immobilizer indicator is blinking (especially if the battery recently went dead and the engine was jump-started).
PROBABLE CAUSE
The immobilizer IMOES code has been erased.
NOTE: This problem occurs only if all these conditions are met: • The security system is set. • The battery goes dead. • Battery power is connected to the vehicle, then disconnected in a very short period of time (milliseconds).
If the vehicle meets these conditions, or if the condition is unknown, go to DIAGNOSIS.
Read more
1984 Mercedes Benz 190E (201 Chassis) Engine Testing Adjustment
The lambda control and the idle speed emissions level must not be tested when the engine is very hot, e.g. immediately after driving sharply or after measuring engine output on the dynamometer.
Testing, adjusting
1 Complete measurement sheet.
2 Switch off air conditioning or automatic climate control. Move selector lever into position “P”.
3 Read out DTC memory. Note: Not available on model year 1984-1986.
Read more
Honda Tech If Your Engine Overheats
The pointer of your car’s tempera- ture gauge should stay in the mid- range under most conditions. It may go higher if you are driving up a long steep hill on a very hot day. If it climbs to the red mark, you should determine the reason. Your car can overheat for several reasons, such as lack of coolant or a mechanical problem. The only indication may be the temperature gauge climbing to or above the red mark. Or you may sec steam or spray coming from under the hood. In either case, you should take immediate action.
Read more
2007 Saturn Aura Engine Technology
Engine experts have dreamt about it, talked about it, and lectured about it, and today – for the first time – General Motors Corp. (GM) is letting outside parties drive the “most awaited advanced combustion technology” of the last 30 years. GM has taken new combustion technology out of the lab and on to the road with GM’s brand new HCCI combustion technology debuts in two driveable concept cars. The system essentially uses diesel-type technology on petrol engines with stunning results. HCCI is used in conjunction with other advanced technologies can result in 15% fuel savings.
Read more
Small Block Chrysler 727 to GM DRCE Engine Adaptor Installation
This Adapter Plate is designed to cover Flexplate only. To protect the Bellhousing area we suggest using the CSR Shield #834. Tech Officials will require a transmission shield. Care must be taken to ensure that this bolt does not Interfere with the Starter Bolt (binding can occur). Starter mountings can vary on DRC Engines. Contact us for Starter Reduction Adaptor Blocks.
Read more
Nissan 200sx SR20DET Engine Tuning Guide
This document explains the engine various modifications, with a common path through them. However, these various modifications can be done in many different orders, and this is merely a guide.
Read more
Engine Torque Link Installation Procedure
1) Remove front engine mount upper bolt with 14mm socket. The front engine mount is located on the timing cover side of the engine also known as the front of the engine.
2) Install the small torque link bracket as shown in picture. Use supplied M10 bolt and tighten to finger tight. A 13mm wrench or socket is used for this bolt. Do not torque down this bolt just yet.
Read more
