Genuine Subaru Performance Parts
A select group of performance and appearance parts to increase your driving pleasure. If you thought you couldn’t love your Subaru more, check out our line of Genuine Subaru Performance Parts to make your vehicle even more fun to own. Engineered specifically to enhance the performance, endurance and, in some cases, the look of your vehicle, these Genuine Subaru Performance Parts allow you to customize, without asking you to compromise the quality and integrity of your Subaru.
Read more
92-95 Honda Civic TD04H-15G Turbo Kit 1.61 VTEC Installation
TURBO KIT INSTALLATION
* Always disconnect the battery negative cable from the battery negative terminal before working on any part of the vehicle.
STOCK PARTS REMOVAL
(1 ) Unplug the O2 sensor and take the exhaust manifold cover from the exhaust manifold. Then, remove the O2 sensor.
(2) Remove the exhaust manifold by removing the nine 8 mm nuts. Inspect the ex. manifold gasket for any damages, replacing the gasket with a new one is recommended.
(3) Remove the stock air filter box, and air intake duct.
Read more
My 2nd gen MM/D50 2.6 Turbo Swap
Donor Starion/Conquest info: Any 1983-1989 2.6 turbo Starion can be swapped. For best stock performance the 1988-89 years are best. The 1987 model year had the highest sales, thus will be more available. It is also easy to upgrade a 1987 to 1988-89 ecu. 1983 is the first year and had a different tbi fuel system then the others years and should be avoided due to parts availability. 1983-85 were non-intercooled, thus would make the swap simpler since don’t need to install an intercooler and needed plumbing. 1986 came both intercooled and non-intercooled.
Read more
RAPID 22 Model FAT01-A6 Owner’s Manual – Assembly/Set-up Instructions
Moving shooting target recommended for factory ammunition in .17 and .22 rim-fire calibers only! Installation Procedures below:
1. Remove all parts from packaging and place on flat work surface. Verify all contents to attached parts list. NOTE: In the event that your unit is damaged or is missing parts please contact Fireaction Inc. at 1.800.767.0879 or contact your local authorized dealer.
2. Place Front Plate (3) on work surface with 90° bends (front) facing down. Next, place plastic Track Plate (4) on top of Front Plate. Lastly, place Back Plate Weldment (7) on top of the Track Plate. All plates should be oriented as shown in Figure-1. NOTE: For proper orientation all bolt holes and shooting window should be aligned.
Read more
Cadillac Stage IV Roller Rocker Assembly
You are the proud owner of the best rocker arm assembly ever produced for the Cadillac 472/500/425 engine family. Though ‘bulletproof’ by design, special precautions should be taken to ensure a long and trouble free life for these assemblies. These exclusive, state of the art parts, were engineered to help you take the performance of your Cad to a whole new level! Please read all instruction thoroughly before installation – aluminum components, adjusters, and other parts may be damaged due to improper installation!
- Pre-oil rocker assemblies before installation; loosen adjuster nuts.
Read more
2003 Nissan 350Z GReddy Turbo Kit (VQ35DE) Twin TD05-18G 8cm2
Factory Parts Removal
When removing the stock parts, make sure you read over the factory repair manual for proper procedures.
- Disconnect the negative terminal of the battery.
- Drain the engine oil, coolant and power steering fluid.
- Disconnect the air flow meter.
- Remove the Air cleaner assembly with airflow meter, intake tube, and breather hose.
- Remove the Top Radiator Hose and the Water Pipe (Located above the Right Exhaust manifold).
- Disconnect the primary and secondary O2 sensor and remove the exhaust manifold and catalytic converter.
- Remove the exhaust manifold.
Read more
2008 Saab 9-3 Turbo X
Saab Turbo X has debuted at MPH Show. With revolutionary XWD system introduced in the car that celebrates 30 years of Saab turbocharging. The premiere of the Saab Turbo X, a driver-focused performance car that sets new standards for the brand. Initially launched at the Frankfurt Motor Show in September, Saab has today announced that only 500 of these limited edition models will be sold.
This model also marks the introduction of XWD, a cutting edge all-wheel drive system that sets performance standards competitors will seek to emulate.
Read more
94-2002 Dodge Turbo Air Guide (TAG & TAG-II) Install
The TAG is intended to be used with the silencer ring in place. On 94-2002 Dodge trucks install the longer side into the turbo housing and the shorter side will be facing the inside of the intake boot. Remove the rubber boot from the turbo charger inlet and insert the TAG into the rubber boot with the longest part of the TAG facing outward as shown. The TAG should snap into the groove inside the boot. Place the supplied band clamp over the hose as shown in the photo below. Slip the boot back over the turbo inlet using one hand through the boot to guide the TAG into the turbo.
Read more
2000-2001 Audi TT 1.8L Turbo Short Throw Shifter Installation Instructions
This B&M Short Throw Shifter has been designed to work on most 2000-2001 Audi TT 1.8L Turbo models. It has been engineered to greatly reduce shift throw and improve shifter feel. The B&M Short Throw Shifter has been designed to work with the stock knob as well as the B&M Knob. Check the parts and tools lists at the beginning of these instructions for the supplied parts and the tools required to install your B&M Short Throw Shifter. Installation of the B&M Short Throw Shifter can be accomplished by anyone with minimal mechanical experience.
Read more
Mazda MX5/Miata AVOTurboworld Bolt-On Turbo Kits
AVOTurboworld has been turbo charging motor vehicles for more than 30 years so it’s no surprise that we know exactly what it takes to make a high quality turbo kit for maximum performance and reliability. AVOTurboworld turbo kits use the highest quality components and manufacturing techniques available in the world. AVOTurboworld kits are designed for minimal installation time and ease of fitment. For example, to help expedite the fitment process, we pre-assemble the turbocharger with the actuator assembly to the manifold and outlet casting.
Read more
