Audi TT 1.8t A.W.E. Tuning DV1 Diverter Valve Installation Instructions
With the DV1 Diverter Valve, we believe you have purchased the finest diverter valve for the money. Follow these instructions, and you’ll have your new A.W.E. Tuning DV1 Diverter Valve installed quickly and easily.
Step 1: Here’s an overview picture of the transverse 1.8T engine found in the Audi TT, VW Golf/Jetta/New Beetle 1.8T. The 225hp TT engine looks a little different, but the install of the A.W.E. Tuning valve is the same procedure. For picture clarity, and ease of install, the decorative engine cover has been removed. Removing the cover is easily done by twisting the “+” shaped fasteners on the cover 90 degrees. They’ll pop up when free, allowing you to grab the cover and lift it up and out of the engine bay. (New Beetle requires removing 2 10mm nuts hidden under trim caps, and then sliding forward and out) We’ve also removed the PCV damper in the following pictures for clarity. You won’t need to remove this item to install the valve.
Read more
Nissan Vent Control Valve Replacement Service Bulletin
All Nissan models using Vent Control Valve P/Ns 14935-AM60A / AM60B
SERVICE INFORMATION
When replacing the EVAP canister vent control valve for any reason: Use the one listed in the PARTS INFORMATION section of this bulletin on Page 2. For vent control valve replacement procedure, refer to the appropriate section of the Electronic Service Manual (ESM) if needed. Read more
1996-Up Nissan Evap Vent Control Valve Diagnostics Service Bulletin
If an applied vehicle has one (or more) of the following DTCs stored in Self Diagnosis, use the Service Procedure below to check the operation of the EVAP vent control valve.
IMPORTANT NOTES:
• If DTC(s) other than the ones listed below are found stored in Self Diagnosis, the EVAP vent control valve is NOT the cause of the incident.
• If the EVAP vent control valve passes the tests outlined in the following Service Procedure, the cause of the incident is NOT the EVAP vent control valve.
Read more
2005 Nissan-Datsun Sentra L4-1.8L Evap Canister Purge Volume Control Solenoid Valve
With CONSULT-II
Check air passage continuity of EVAP canister purge volume control solenoid valve
under the given conditions.
Without CONSULT-II
Check air passage continuity of EVAP canister purge volume control solenoid valve
under the given conditions.
Read more
Stratmosphere HyperBoost Valve (Audi S4) Installation Instructions
Step 1- Remove motor cover
This is the small triangular cover in the front of the engine where the dipstick is located (figure 1). Just twist the two screws 90 degrees counterclockwise. Then lift up the cover. The cover fits onto a rubber round mount at the point on the “triangle” as well. It’s just pressed on there.
Read more
58 mm LT1 NOS Throttle Body for the 1994-97 Chevrolet
These instructions must be read and fully understood before beginning installation. Failure to follow these instructions may result in poor performance, vehicle damage, personal injury, or death. If these instructions are not fully understood, installation should not be attempted.
Read more
Chevy/GMC 2WD, 4WD Body Lift Installation Instructions
This body lift kit should only be installed on vehicles in good working condition. Before installation, the vehicle should be thoroughly inspected for evidence of corrosion or deformation of the sheet metal around the factory body mounts. This body lift kit should not be installed on any vehicle that is suspected to have been in a collision or misused. Off-road use of your vehicle with this body lift installed may increase the stress applied to the factory body mounts. We do not recommend that any vehicle with a body lift installed be involved in any extreme off-road maneuvers such as jumping. Failure to observe this warning may result in serious personal injury and/or severe damage to your vehicle.
Read more
Crower Valve Train Components
This booklet is a general installation reference guide for Crower valve train components. The information is intended to give you a good basic idea of what building a reliable and powerful performance valve train requires. We’ve tried to eliminate the “surprises” and provide you with solutions to any snags you might encounter. It should help minimize your anxiety when there’s more to a job than you planned on, or when parts don’t fit properly.
Read more
2003-07 Dodge Dakota 4.7L PowerAid Throttle Body Spacer
Your PowerAid Throttle Body Spacer was carefully inspected and packaged. Check that no parts are missing, or were damaged during shipping. If any parts are missing, please contact AIRAID.
Installation Instructions. Read Me!
1. DISCONNECT NEGATIVE (-) BATTERY CABLE.
2. Remove air intake hose assembly.
3. Remove throttle body air intake box and save bolts.
4. Remove (3) bolts from the throttle body.
Read more
GRIP Chevy Cobalt Body Kit Installation
All GRIP body kits need to be properly sanded and primed before painting, even if the part arrives pre-primed. Failure to properly prepare parts before painting can result in poor paint finish and adhesion. Please prefit parts before painting! Once a part has been painted or modified in any way it cannot be returned.
1: Look over vehicle before installing the body kit to make note of all attachment points on existing fascia. Since GRIP uses all existing attachment points, it is very important not to harm existing mounting holes and / or fasteners. Some fasteners that are drilled out cannot be reused. It is very important to use special care when removing the reusable fasteners from the panels since they will not be provided by GRIP. GRIP only provides non-reusable fasteners with its kits.
Read more
