HID Kit Xenon Installation Instructions
The Chemical gases, most of which are xenon and iodides, are filled the quartz tube of the light. Through the ballast, then the voltage of 12V DC will be increased to 23KV immediately: the electrons of the xenon in the tube will be dissociated because of the voltage swing and thus an electrical arc happens between the two poles. Xenon light is power saving, safe and has long life, high luminance. In addition of the use of the UV-cut quartz tube, the light is crystal forever.
Read more
Chevy/GMC 2WD, 4WD Body Lift Installation Instructions
This body lift kit should only be installed on vehicles in good working condition. Before installation, the vehicle should be thoroughly inspected for evidence of corrosion or deformation of the sheet metal around the factory body mounts. This body lift kit should not be installed on any vehicle that is suspected to have been in a collision or misused. Off-road use of your vehicle with this body lift installed may increase the stress applied to the factory body mounts. We do not recommend that any vehicle with a body lift installed be involved in any extreme off-road maneuvers such as jumping. Failure to observe this warning may result in serious personal injury and/or severe damage to your vehicle.
Read more
01-06 Chevy/GMC 2500 HD 4×4 3″ Suspension lift Installation Part #C9381K
Make sure you park the vehicle on a level concrete or asphalt surface. Many times a vehicle is un-level (side-to-side) from the factory, but usually not noticed until a lift kit has been installed which makes the difference more visible. Using a measuring tape, measure the front and rear (both sides) from the ground up to the center of the fender opening above the axle. Record below for future reference.
Read more
2008 Jeep Liberty 2WD/4WD 2″ Polyurethane Spacer Lift Installation Instructions
Make sure you park the vehicle on a level concrete or asphalt surface. Many times a vehicle is not level (side-to-side) from the factory & is usually not noticed until a lift kit has been installed which makes the difference more visible. Using a measuring tape, measure the front & rear (both sides) from the ground up to the center of the fender opening above the axle. Record this information below for future reference.
Read more
94-01 Dodge 1500 Lift Kit
This kit is packaged as a leveling kit—raising the front 5” and the back 4”. If you desire a different look or if your truck has a tool box or added weight in the rear please consult with your sales representative about other block and u-bolt options or the use of an add-a-leaf. The 5” suspension system was developed for a 35×12.50×15 tire on an after market wheel with 5” of back spacing.
Read more
Air Lift Leveling Kit Installation Instructions
1. Jack up rear of vehicle or raise on hoist. Support frame with safety stands. Lower axle or raise body of vehicle until suspension is fully extended.
2. Remove plastic cap from barbed stem on end of cylinder. Exhaust the air from the cylinder by rolling it up toward barbed stem on the end of the cylinder. Replace the cap on the stem to hold flattened shape.
3. Follow the steps below for the specific make of your particular vehicle.
Read more
Hy-Tech Wheel-Lift Installation (Pickup)
1.) Rear Leaf Springs: We strongly recommend that you increase the number of leafs in the rear main springs before you begin the installation process. In most cases we have found that these additional leafs (Dodge – 4 leafs, Chev. – 3 leafs and Ford – 2 leafs), in addition to an in-cab controlled airbag system, will be adequate in most cases. The use of an airbag system has always proven to be far more effective than additional helper/overload springs.
Read more
2007-2008 Chevy 1500 Pickup 2″ Suspension Lift Kit
DISASSEMBLY AND ASSEMBLY OF DIFF DROP KIT
1. Remove the 2 diff bolts on driver side differential that attach the diff housing to the frame mount. Install diff spacers (P/N C3DB) using new M12 X 1.75 X 50 bolts. This is to space the diff down ―” to improve the angle on the CV boots. See Fig. A
2. Repeat this process on the passenger side of the vehicle. Remove the 2 OEM diff nuts on passenger side differential that attach the housing to the frame. Install diff spacers (P/N C3DA) utilizing the supplied M12 x 1.75 nylon locking nuts.
Read more
2008 Peugeot 308
Designed by Peugeot’s in-house designers, the Peugeot 308 builds on the successful concept of the Peugeot 307, with its semi-high architecture, large interior space, class leading safety equipment and high standards of road holding. The stylish design not only looks good but contributes to reducing fuel consumption and emissions, due to its class leading aerodynamics – Cx of 0.29 – enabling the 1.6 litre HDi 90 to emit only 120 g/km of CO2.
Read more
2008 Audi A4 Cabriolet 2.0 TFSI Special Edition
The new A4 2.0 TFSI S line Special Edition combines styling enhancements with extra interior luxuries to create one of the most covetable Cabriolets this side of the RS 4.
Special version of sought-after A4 Cabriolet powered by 2.0 Turbo FSI 200PS engine. Exceptional specification includes S line exterior styling, Pearl Nappa leather upholstery, BOSE sound system with CD autochanger, acoustic parking and xenon headlamps – 200PS @ 5,100-6,000rpm, 280Nm @ 1,800-5,000rpm, 0-62mph in 8.2 seconds (multitronic 8.1), top speed 146mph (multitronic 144), combined mpg 34.0 (multitronic 33.6), CO2 199g/km (multitronic 199g/km)
Read more
