2002-2005 Nissan 350Z Stillen Headers Installation Instructions
Installation:
1. Start install by raising vehicle to a suitable working height. Observe proper safety precautions when working under vehicle.
2. Disconnect negative terminal of battery. Remove the air inlet tube and airbox from the driver’s side of vehicle. On the passenger side move any brackets and/or harnesses that may interfere with access to the manifold bolts or heat shields.
3. Remove the lower splashguard from the vehicle. Remove the 4 nuts securing the ‘Y’ pipe to the back of the catalytic converters. Note: Nissan recommends that all locking nuts and gaskets be replaced after removal.
Read more
2002-2007 Subaru Impreza WRX/STI Front Mount Intercooler
1) Raise hood and disconnect battery.
2) Remove existing intercooler by removing (2) 12mm bolts, and (2) hose clamps. Remove Throttle Body Coupler. (1) hose clamp.
3) Remove intercooler support brackets, (2) 12mm bolts on drivers side bracket, and (2) 12mm bolts on passenger side bracket.
4) Remove intake system up to turbo inlet hose. This includes removing the rubber intake elbow (2 hose clamps), filter box (2 12mm bolt located on chassis), and resonator box (2 10mm nuts). Resonator box can be better reached when bumper is removed.
5) Remove coolant overflow tank (either 2 10mm bolts, or one clip) from radiator & drain into suitable container. NOTE: Coolant will be reused later.
Read more
1992-95 Cadillac Eldorado & Seville Pro.Vit VSM Installation
STEP 1. Begin by removing the small black trim ring that surrounds the radio. Insert the hook tool behind the upper right corner of the trim ring and pull toward you to loosen the ring. Once the ring is loose, work the remaining three (3) corners of the trim ring loose. Set the trim ring aside. Turn the ignition to the “ON” position and shift the transmission into low gear. Just above the ashtray door, grasp the top section of the bezel that surrounds the transmission shifter and pull toward you to release two (2) clips. Insert the hook tool behind the right rear corner of the bezel just behind the shifter. Pull upward to release one (1) clip. Perform the same action in the left rear corner releasing one (1) more clip. Grasp the rear of the bezel and continue working loose two (2) clips on the left and right sides of the shifter. Work the bezel up and over the shifter knob and disconnect all wiring. Set the bezel aside.
Read more
Audi TT 1.8t A.W.E. Tuning DV1 Diverter Valve Installation Instructions
With the DV1 Diverter Valve, we believe you have purchased the finest diverter valve for the money. Follow these instructions, and you’ll have your new A.W.E. Tuning DV1 Diverter Valve installed quickly and easily.
Step 1: Here’s an overview picture of the transverse 1.8T engine found in the Audi TT, VW Golf/Jetta/New Beetle 1.8T. The 225hp TT engine looks a little different, but the install of the A.W.E. Tuning valve is the same procedure. For picture clarity, and ease of install, the decorative engine cover has been removed. Removing the cover is easily done by twisting the “+” shaped fasteners on the cover 90 degrees. They’ll pop up when free, allowing you to grab the cover and lift it up and out of the engine bay. (New Beetle requires removing 2 10mm nuts hidden under trim caps, and then sliding forward and out) We’ve also removed the PCV damper in the following pictures for clarity. You won’t need to remove this item to install the valve.
Read more
Audi A4 B6/8E 5 Speed Short Shifter Installation Manual
Start by ensuring that the engine is switched off and the hand brake is set.
Step 1: Removal of console cover plate and shift knob.
To remove the cover plate, open the ashtray and pull up on the front of the cover. Do the same for the rear of the cover by lifting from within the shift boot at the rear side.
To remove the shift knob you must cut the clamp holding the shift knob we have included a new one in the kit
Once you have removed the clamp, pull up on the shift knob to remove it.
Read more
