2003-2007 Nissan Murano Engine Air Intake Duct Service Bulletin
Nissan is conducting a voluntary safety recall on model year 2003 – 2007 Murano vehicles. Under certain conditions, the intake duct, which is connected to the intermediate resonator in the air intake system of the engine, may separate from the resonator with engine movement. This could cause minor idle fluctuation or poor acceleration. If this occurs, and the vehicle continues to be driven without being serviced, the engine may stall while driving. To remedy this potential condition, Nissan is conducting this voluntary safety recall campaign to replace the air intake duct with an updated part and the air duct clamps with new clamps at no charge for parts or labor.
Read more
94-2002 Dodge Turbo Air Guide (TAG & TAG-II) Install
The TAG is intended to be used with the silencer ring in place. On 94-2002 Dodge trucks install the longer side into the turbo housing and the shorter side will be facing the inside of the intake boot. Remove the rubber boot from the turbo charger inlet and insert the TAG into the rubber boot with the longest part of the TAG facing outward as shown. The TAG should snap into the groove inside the boot. Place the supplied band clamp over the hose as shown in the photo below. Slip the boot back over the turbo inlet using one hand through the boot to guide the TAG into the turbo.
Read more
Subaru Impreza Hatchback PN-140325 Exhaust System Installation
Borla Performance Cat-Back™ Exhaust System (Part Number 140325) has been designed for the Subaru Impreza Hatchback equipped with a 2.5L opposed 4 cylinder engine (non-turbo), all-wheel drive and automatic or manual transmissions.
Borla Performance Cat-Back Exhaust System Installation
1. Using the original hardware, place the front pipe assembly into position supporting it with a stand at the open end. Hand tighten the hardware for now. (See figure 3)
Read more
2009 Toyota Corolla 1.8L Tuned air Intake System
Prior to starting the installation, remove the 2 plastic clips inside of the grill. This is an illustration to show you how to remove the front bumper. Start by removing all plastic clips and screws as shown above, once all clips and screws have been removed continue to pull the front bumper off. The two plastic clips are removed from side of the wheel well prior to pulling the bumper off. Once all plastic clips and screws have been removed, continue to pull off the bumper. Depress the tab and pull the electrical harness connector from the mass air flow sensor. The harness clip is pulled out from the air box attachment as shown above. The stock screws are loosened and removed from the mass air flow sensor. The Read more
94-95 Mustang GT 5.0 HO Smog System Removal
This is a ‘How To’ article to remove the smog system from a ’94-’95 SN95 5.0 HO Mustang GT and installing a delete pulley kit in its place. I tried to include everything as best as possible but take note that some of the elements may not be outlined. Use this article at your own risk. Consult your local laws regarding emissions prior to proceeding with this project. Should you require any further information in regards to this ‘How To’ see my contact info at the end of the article and I will help to the best of my knowledge.
Read more
2001-2005 Chevy 6.6L Cat Back 4″ K4110A Installation
Removal of Original System
1) Start under the vehicle. Find the four bolt flange just behind the catalytic converter, loosen and remove the bolts on this flange.
2) Cut the original system just behind the muffler.
3) Spray the stock hangers with aerosol lube and pry rubber mounts from the system. Leave the rubber mounts attached to the truck for re-use.
4) Remove the old system.
Read more
Kia System Information Service (KSIS) Service Manual & Wiring Diagrams Repair
REMOVAL Disconnect the negative battery cable. Remove the two fresh air duct mounting bolts on the radiator. Loosen the fresh air duct clamp at the intake housing. Remove the hose at the resonance chamber. Remove the frech air duct. Remove the five cooling fan shroud bolts. Remove the four thermo-modulated fan nuts. Remove the four thermo-modulated fan cooling fan shroud at the same time. Loosen the two generator mounting bolts(A and B). Loosen the generator drive belt from the generator by loosening the adjusting bolt(C). Remove the generator drive belt. Remove the fan pulley. Remove the four splash guard mounting bolts and splash guard. Loosen the A/C idler puller nut(A). Read more
2006 Toyota Corolla Air Conditioning Unit Assy
HINT: Installation is in the reverse order of removal.
1. DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM SST 07110-58060 (07117-58080, 07117-58090, 07117-78050, 07117-88060, 07117-88070, 07117-88080)
2. DISCONNECT SUCTION HOSE SUB-ASSEMBLY
a. Install SST to piping clamp. SST 09870-00015 HINT: Confirm the direction of the piping clamp claw and SST using the illustration showing on the caution label.
b. Push down SST and release the clamp lock. NOTE: Be careful not to deform the tube, when pushing SST.
c. Pull SST slightly and push the release lever, then remove the piping clamp with SST.
Read more
2007-2008 Dodge Avenger & Chrysler Sebring Exhaust System Installation
With a used vehicle, we suggest a penetrating spray lubricant to be applied liberally to all exhaust fasteners and allowing a significant period of time for the chemical to lubricate the threads before attempting to disassemble.
1. Remove the ground strap from the muffler at the rear of the vehicle as shown in figure 1.
2. Unbolt the clamp located just behind the catalytic converter as shown in figure 2.
3. Lubricate all the hangers and rubber isolators.
4. Using a muffler stand or an additional person to hold the exhaust system into position, remove all the hangers from the rubber isolators and remove the exhaust system from the vehicle.
Warning: Use extreme caution during installation. Torque all fasteners according to manufacturer’s torque values and tightening sequence. DO NOT use air impact tools to tighten fasteners on Borla Performance Exhaust Systems. Use of such tools may result in bent flanges or gasket contact areas leading to exhaust leaks.
Read more
1993 Jeep Grand Cherokee Wheel Alignment
WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES 1993 WHEEL ALIGNMENT Chrysler Corp. – Specifications & Procedures
ADJUSTMENTS CAMBER MEASUREMENT
Check camber to determine if any components are bent or damaged. Camber angle is NOT adjustable. If angle is not to specification, components causing problem must be replaced. See ALIGNMENT SPECIFICATIONS .
CASTER ADJUSTMENT
Check caster angle. See ALIGNMENT SPECIFICATIONS . If caster is not to specification, adjust by adding or removing shims at rear of lower control arms on all except Wrangler, or between front axle pads and spring brackets on Wrangler. See Fig. 1 or Fig. 2 .
Read more
