03-05 Chrysler PT Cruiser Turbo P/N 300-138 Installation
Remove the Factory Air Box Lid
a) Loosen the clamp on the factory intake tube at the air box lid.
b) Unclip the factory air box lid and remove from vehicle.
c) Extract the factory air filter box assembly. (Note: leave the base in place)
d) Unclip and remove the small intake tube attached to the factory air filter box.
e) Replace the factory air filter box in its original place and re-connect the hose it its original location.
Read more
1991 Saab 9000 L4-2290cc Axle Shaft Assembly
Removal
Important: Thorough cleanliness must be observed during all work on drive shafts and
drive shaft joints, to prevent dirt and dust getting into the joints. Before starting work,
always clean the wheel arch, MacPherson strut and other areas around the drive shaft
and joints.
1 Unfasten the hub centre-nut.
2 Lift the car and remove the wheel.
3 Remove the hub centre-nut.
Read more
MSD Pro Mag 12 LT Chrysler PN 7910 Installation
1. Install the set screw into the intake manifold or engine block.
2. Install the magneto into the engine. On Chevrolet engines, position it so the hold down clamp will align with the housing’s anti-rotation collar.
3. Install the billet clamp over the set screw and on to the collar of the magneto. Put the flat washer, lock washer and the nut onto the stud and tighten the assembly.
Read more
2005 Chevrolet Cobalt Exhaust System Installation
Borla Performance Cat-Back ™ Exhaust System Installation
1. Using the hardware supplied, place the front muffler assembly up into position as shown in figure 5 making sure to install the hangers into the rubber isolators. Hand tighten the hardware for now.
2. Place a clamp over the expanded end of the intermediate pipe and set it into position as shown in figure 6 installing the hanger into the rubber isolator. Do Not tighten the clamp.
3. Place a clamp over the expanded end of the rear muffler assembly and set it into position as shown in figure 7 making sure to install the hangers into the rubber isolators. Do Not tighten the clamp.
Read more
Stratmosphere HyperBoost Valve (Audi S4) Installation Instructions
Step 1- Remove motor cover
This is the small triangular cover in the front of the engine where the dipstick is located (figure 1). Just twist the two screws 90 degrees counterclockwise. Then lift up the cover. The cover fits onto a rubber round mount at the point on the “triangle” as well. It’s just pressed on there.
Read more
00-05 Audi 2.7T Engines A.W.E. Tuning DV1 Diverter Valves Installation Instructions
Removal of stock valves:
Removal of the stock diverter valves requires removal of decorative engine cover with the “V6 BITURBO” badging. Lift off the cover after twisting X-shaped plastic fasteners 90 degrees with a flat blade screw driver. Valve replacement is much easier done on a cool engine.
Read more
2007 Audi RS4 Exhaust System Installation
Borla Performance Cat-Back™ Exhaust System (Part number 140251) has been designed for the 2007 Audi RS4 equipped with 4.2L V8 engine, all-wheel drive and automatic or manual transmissions. Borla Performance Industries recommends that an exhaust shop or professional after market parts installer, who has all the necessary equipment, tools and experienced personnel needed for proper installation, should perform the installation of this system. However, if you decide to perform the installation, we recommend someone should help you. Ensure the installer uses all under car safety precautions including eye protection.
Read more
2002-up AUDI A4 1.8t AWD 21mm Rear Anti-Roll Bar Installation Instructions
1. Park car on a flat, level surface capable of supporting the vehicle’s weight on jack and jack stands.
2. Using the manufacturers recommended lifting point(s), raise rear of vehicle and support with jack stands. NEVER WORK ON A VEHICLE SUPPORTED ONLY WITH A JACK!
3. Release left and right muffler from hangar and allow exhaust to droop.
4. Remove four mounting bolts (13mm hex) and two end link bolts (16mm hex). Remove anti-roll bar from vehicle.
5. Prepare sub-frame and brackets for welding by removing paint from surfaces around weld areas.
Read more
NewSouth Performance Mk5/EOS/B6 TurboPod kit Installation
This document outlines how to install a NewSouth Performance Mk5/EOS/B6 TurboPod kit1. Please review this document before attempting your installation.
INSTALLATION INSTRUCTIONS
Use appropriate safety precautions at all times. Make sure car in securely parked and on a level surface. Remove positive terminal of battery when working with electricity.
Read more
Audi TT 1.8t A.W.E. Tuning DV1 Diverter Valve Installation Instructions
With the DV1 Diverter Valve, we believe you have purchased the finest diverter valve for the money. Follow these instructions, and you’ll have your new A.W.E. Tuning DV1 Diverter Valve installed quickly and easily.
Step 1: Here’s an overview picture of the transverse 1.8T engine found in the Audi TT, VW Golf/Jetta/New Beetle 1.8T. The 225hp TT engine looks a little different, but the install of the A.W.E. Tuning valve is the same procedure. For picture clarity, and ease of install, the decorative engine cover has been removed. Removing the cover is easily done by twisting the “+” shaped fasteners on the cover 90 degrees. They’ll pop up when free, allowing you to grab the cover and lift it up and out of the engine bay. (New Beetle requires removing 2 10mm nuts hidden under trim caps, and then sliding forward and out) We’ve also removed the PCV damper in the following pictures for clarity. You won’t need to remove this item to install the valve.
Read more
