2003-2007 Nissan Murano Engine Air Intake Duct Service Bulletin
Nissan is conducting a voluntary safety recall on model year 2003 – 2007 Murano vehicles. Under certain conditions, the intake duct, which is connected to the intermediate resonator in the air intake system of the engine, may separate from the resonator with engine movement. This could cause minor idle fluctuation or poor acceleration. If this occurs, and the vehicle continues to be driven without being serviced, the engine may stall while driving. To remedy this potential condition, Nissan is conducting this voluntary safety recall campaign to replace the air intake duct with an updated part and the air duct clamps with new clamps at no charge for parts or labor.
Read more
94-2002 Dodge Turbo Air Guide (TAG & TAG-II) Install
The TAG is intended to be used with the silencer ring in place. On 94-2002 Dodge trucks install the longer side into the turbo housing and the shorter side will be facing the inside of the intake boot. Remove the rubber boot from the turbo charger inlet and insert the TAG into the rubber boot with the longest part of the TAG facing outward as shown. The TAG should snap into the groove inside the boot. Place the supplied band clamp over the hose as shown in the photo below. Slip the boot back over the turbo inlet using one hand through the boot to guide the TAG into the turbo.
Read more
Subaru Impreza Hatchback PN-140325 Exhaust System Installation
Borla Performance Cat-Back™ Exhaust System (Part Number 140325) has been designed for the Subaru Impreza Hatchback equipped with a 2.5L opposed 4 cylinder engine (non-turbo), all-wheel drive and automatic or manual transmissions.
Borla Performance Cat-Back Exhaust System Installation
1. Using the original hardware, place the front pipe assembly into position supporting it with a stand at the open end. Hand tighten the hardware for now. (See figure 3)
Read more
2004+ Subaru Impreza WRX/STI Front Lip (polyurethane)
Polyurethane is a flexible material. Occasionally during shipping, sections of the lip may warp or bend in unusual shapes. DO NOT WORRY! Simply lay the lip flat and out in the sun for a day and it will return to its normal shape. To cure the waviness of the front portion, simply purchase a long metal or wood section, clamp this metal section inside the lip (clamps can be purchased at Home Depot), and lay out in the sun for about a day. This will fix the waviness problem.
Read more
Honda CR-V DVD Navigation Attachment
DVD AVN Navigation Unit P/N: 08A40-1J6-100
Wire Harness Routing Precaution
Disconnect the connectors and terminals by holding them. Do not pull the harness to disconnect the connector.
Do not pull the harness with force. it will damage the har ness.
Cut off the excess of the wire ties.
Connect the connectors and terminals securely until they lock.
Reinstall the connectors to the corresponding stays whenever they are removed. After operation, check that the connectors are installed on the stays securely and not loose or come out of the stays.
Read more
Power Steering, Air Cleaner Element
Always use Genuine Honda Power Steering Fluid. If it is not available, you may use another power steering fluid as an emergency replacement. However, continued use can cause increased wear and poor steering in cold weather. Have the power steering system flushed and refilled with Honda PSF as soon as possible. A low power steering fluid level can indicate a leak in the system. Check the fluid level frequently and have the system inspected as soon as possible.
Read more
94-95 Mustang GT 5.0 HO Smog System Removal
This is a ‘How To’ article to remove the smog system from a ’94-’95 SN95 5.0 HO Mustang GT and installing a delete pulley kit in its place. I tried to include everything as best as possible but take note that some of the elements may not be outlined. Use this article at your own risk. Consult your local laws regarding emissions prior to proceeding with this project. Should you require any further information in regards to this ‘How To’ see my contact info at the end of the article and I will help to the best of my knowledge.
Read more
2008 Chevy Classic Duramax V8 6.6L LBZ, LLY Part P7075 Installation
You have just purchased the best engineered and most advanced air intake system, equipped with Ea nano-fiber air filter. Please check the contents of this box immediately. Report any defective or missing parts to the authorized Injen or AMSOIL dealer you purchased this product from.
Before installing any parts of this system, please read the instructions thoroughly. If you have any questions regarding installation, please contact your dealer, Injen Technology or AMSOIL. Installation DOES require some mechanical skills. A qualified mechanic is always recommended.
Read more
2007 Toyota Camry Hybrid Sirius XM Radio Satellite Installation
Cable Routing and Installation (a) Install and route the tuner cable from the center cluster and along the front support bar. (Fig. 3-1) (b) Provide sufficient cable slack to connect to the tuner, and then secure the cable to the existing wire harness with lock tie. Cut excess off lock tie. Connect wire harness to head unit. (c) Using lock ties attach to existing W /H. Trim lock tie excess. (Fig. 3-2) (d) Route to the existing clamps. (Fig. 3-2) (f) Route the cable as shown and secure with lock tie. Trim lock tie excess. (Fig. 3-4) (g) Route the tuner cable under the rear passenger seat and secure with cushion tape. (Fig. 3-5) NOTE:Clean the area for the cushion tape with the approved cleaner.
Read more
1994 Nissan Maxima SE Axle Shafts Installation
On A/T models, right axle shaft must be removed to remove left axle shaft. On all models, cover axle shaft boots with shop towel to prevent damaging boots. Always use NEW snap rings, circular clips and boot clamps during reassembly and installation. Replace axle shaft oil seal in differential before installing axle shaft.
Read more
