Subaru Fuel Injector Removal Procedures
When removing and/or replacing the fuel injector(s), it’s imperative that the below instructions be strictly followed. Failing to do so may result in damage to the injector(s).
Applicability: All Legacy, Impreza and SVX models.
Note: Pliers or any other tools not specified in these instructions should not be used under any circumstances to prevent damage to the fuel injector(s).
Read more
1998–2001 Cadillac Catera Auto Off Traction Control System Kit
The Auto Off TCS Kit was designed for GM vehicles using Traction Control Systems (TCS). After installation, this Auto Off TCS Kit provides the antilock brake system/traction control system with a ‘Turn Off’ signal 10 seconds after the ignition is turned On. This means the vehicle will start up with the TCS turned Off rather than the original turned On state. The Auto Off TCS Kit is very easily installed and does not require any original wiring to be cut. All wiring connections are completed using simple and effective wire taps with connectors.
Read more
FTDRL Install for a Chevy Avalanche
Ok, I have been getting a lot of questions about this mod and I know the directions are out there, but I wanted to make a very clear step-by-step set of instructions for the electrically challenged people (like me!). Not to mention 2002 directions get mixed in on some older threads and it gets confusing.
Here are the directions for the diode method for 2003-2006 Avalanches to get:
• FTDRL’s (Full-Time Daytime Running Lights) and
• All-On-High (High/Lows/Fogs/DRL come on when switching to high beams or using “flash to pass”)
Read more
2002 Taurus/Sable Heating and Ventilation Workshop Manual
All Vehicles NOTE: If a heater core leak is suspected, the heater core must be pressure leak tested before it is removed from the vehicle. For additional information, refer to Section 412-00 .
1. Remove the instrument panel (04320). For additional information, refer to Section 501-12 .
2. Remove the right-side cowl vent screen (018A16).
3. Remove the screws and the water shield (02254).
4. Using suitable hose pinching pliers, clamp the heater hoses. Disconnect the heater hoses. Vehicles with EATC
Read more
2006 Toyota Corolla Air Conditioning Unit Assy
HINT: Installation is in the reverse order of removal.
1. DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM SST 07110-58060 (07117-58080, 07117-58090, 07117-78050, 07117-88060, 07117-88070, 07117-88080)
2. DISCONNECT SUCTION HOSE SUB-ASSEMBLY
a. Install SST to piping clamp. SST 09870-00015 HINT: Confirm the direction of the piping clamp claw and SST using the illustration showing on the caution label.
b. Push down SST and release the clamp lock. NOTE: Be careful not to deform the tube, when pushing SST.
c. Pull SST slightly and push the release lever, then remove the piping clamp with SST.
Read more
1986-1999 GM Bonneville/Eighty Eight/LeSabre Heater Core Removal/Installation
For 1987-91 Vehicles
1. Disconnect the negative battery cable. Drain the coolant into a clean container for reuse.
CAUTION
When draining the coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze, and are quite likely to
drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain
the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.
2. Remove the right side sound insulator. Remove the underdash and splash cover covering the heater hoses in the engine
compartment.
Read more
U-Cut-To-Fit GM & Chrysler Speedometer Cable Kit Installation Instructions
U-Cut-To-Fit Speedometer Cable Kit Installation
Step 1: Install outer housing to speedometer and route housing to transmission, making sure to keep away from exhaust pipes.
Step 2: Hold housing up to transmission to determine length and mark a cut line. Remove housing from vehicle and cut housing at the cut line.
Step 3: After cutting housing, install end of housing into GM or Chrysler trans end fitting. Figure 1 Slide housing nut up and tighten until housing is locked into fitting.
Note: Do Not over tighten nut as it will result in fitting failure.
Read more
2006 Audi A3 2.0FSI/VW MK5 Golf Carbonio Intake System Installation Instructions
Please take the time to fully read over these instructions before attempting to install the kit. This will greatly speed up the installation process and minimize any difficulties you may encounter.
Tools Required:
- Large opening pliers
- Torx T-20 socket tip
- Ratchet with extensions
- Flat head screwdriver
- Phillips head screwdriver
Read more
Stratmosphere HyperBoost Valve (Audi S4) Installation Instructions
Step 1- Remove motor cover
This is the small triangular cover in the front of the engine where the dipstick is located (figure 1). Just twist the two screws 90 degrees counterclockwise. Then lift up the cover. The cover fits onto a rubber round mount at the point on the “triangle” as well. It’s just pressed on there.
Read more
1999.5-2001 Audi A4 (B5) HID conversion installation instructions
1. Take the kit out of the box and lay everything out. You can install either the ballasts or bulbs first but typically it is easier to install the bulbs first.
2. There are 3 T27 torx screws holding the headlight on. The 2 on top are visible in this picture.
3. with the 2 screws removed.
4. The third screw is shown here. A long extension is needed to get to it and an extendable magnet is helpful to retrieve the screw (or bit if it falls).
5. Disconnect the headlight and turn signal connectors and remove the headlight by pulling it toward the outside of the car and toward you.
Read more
