Camshaft Installation Instructions for Nissan GA16DE Engines
1. It is highly recommended that an oil and filter change be done before installing new cams.
2. Remove the distributor, and valve cover from the engine. Use caution not to drop anything into the engine.
3. With the parking brake on, and the car out of gear (neutral), rotate the crankshaft clockwise until #1 cylinder is at TDC (top dead center) with all of it’s valves closed. To insure that this Step 2 is correct, look at the crank pulley (TDC is the second mark from the left, it will Read more
Rally Armor Subaru Impreza WRX/STI/RS/2.5i – 2002-2007 Mud flap Mounting Instructions
Rally Armor recommends professional installation – Cautionary Note: The hardware is quite strong and self-threading but overtightening the clips is not recommended.
FRONT MUD FLAP installation:
Step 1: Remove the clips (1-4) and the two side skirt clips in the front to gain access to the body. Cautionary Note: Be careful not to rip the wheel well plastic. It tears easily. Pull back slowly!
Step 2: Pull the liner back and the side skirt down slightly.
Read more
Chevrolet Van 97 & Up Sway Bar Installation
This bar was designed to replace your original equipment sway-bar. The diameter of the bar has been increased for more roll resistance; the contours of the bar may differ slightly, if some of the bends were not necessary. This kit may come with none, some or all of the hardware required to install the bar depending on the application. If hardware is not included with the kit, the hardware from the O.E. bar must be retained and re-used. If these parts are too worn to be re-used it will be necessary to obtain them from your O.E. parts dealer. If your car/truck was not equipped with O.E. bar, the installation of this bar may not be possible.
Read more
1995-1997 Eagle Talon Short Throw Shifter Installation Instructions
This B&M Short Throw Shifter has been designed to work on most 1995-1997 Eagle Talon, 1995-1996 Dodge Avenger, 1995-1996 Chrysler Sebring, and 1995-1999 Mitsubishi Eclipse models equipped with a manual transmission. It has been engineered to greatly reduce shift throw and improve shifter feel. Check the tool list at the end of these instructions for the tools required to install your B&M Short Throw Shifter. Installation of the B&M Short Throw Shifter can be accomplished by anyone with minimal mechanical experience.
Read more
1996-1998 ACURA 3.5 RL w/o GPS Part Number AC-55-96 Instructions
STEP 1. Begin by inserting the hook tool underneath the right rear corner of the black trim bezel that surrounds the shifter lever. Pull upward to release one (1) plastic clip. Perform this same action in the remaining three (3) corners on the bezel, releasing three (3) more plastic clips. Slide the bezel over the shifter knob and disconnect all wiring. Set the bezel aside. Remove the wood grain trim bezel that surrounds the shifter. This bezel also has the ashtray integrated into it. Insert your hook tool underneath the right rear corner of this bezel and pull upward to release right rear clip. Insert the hook tool underneath the left rear cor- ner of the bezel and pull upward to release left rear clip. There are two more clips holding the bezel in place located in front of the shifter just behind the ashtray. Insert your hook tool between the center console padding and the trim bezel on the right side of bezel. Pull upward to release clip. Perform this same action on the left side. Grasp the Read more
Exhaust System Installation For 2007 Toyota Camry LE/SE/XLE
Original Exhaust System Removal
Note: With a used vehicle, we suggest a penetrating spray lubricant to be applied liberally to all exhaust fasteners and allowing a significant period of time for the chemical to lubricate the threads before attempting to disassemble.
1. Unbolt the flanges shown in figure 1 located just in front of the muffler assemblies. Place the nuts to the side for use during the installation of your new exhaust.
2. Lubricate all the hangers and rubber isolators.
3. Using a muffler stand or an additional person to hold the right muffler assembly in place, remove the hangers from the rubber isolators and then remove muffler as shown in figure 2.
4. Repeat step 3 for the removal of the left side muffler assembly.
Read more
1992-96 Toyota Camry Pro.Fit Part Number TY-50-92 Installation Instructions
All instructions assume a drivers seat vantage point. Caution is advised when removing and reassembling wood or plastic parts of a dash. Applying unnecessary force or pressure may cause a piece to crack or break. Pro.Fit logo and part number will be right side up and readable when installed.
TOOLS REQUIRED: #2 Phillips screwdriver, hook tool.
PARTS INCLUDED: Pro.Fit VSMTM, instructions.
LOCATION: To the right of the radio.
Read more
Toyota Prius GEN 2 Passenger Extender Install Guide
Installation Guide: Thank you for purchasing extendmyseat brackets. Please follow the directions carefully and within 30 minutes you will be loving your new seats.
Inventory in Box:
2- extendmyseat brackets
4- black 3/8 x ¾’ stainless grade 8 bolts
1- M10 x 125 by 1.35” grade 8.8 bolt w/ washer
What you will need for assembly:
1- socket wrench
1- 9/16 socket & 1 11/16 SOCKET
1- Metric 13 socket (Prius uses metric bolts however a 9/16
works)
1- 9/16 flat wrench
1- 3/32 allen wrench
1- protective eyewear
Step 1- Remove the 2 Black extendmyseat brackets from the packaging and locate the 4 black 3/8” provided bolts.
Step 2- Go to your vehicle with a socket wrench, a 3.32 allen wrench and a 9/16 socket, eye protection and your keys. Remember to turn off your cabin lights.
Read more
ASWI-X Universal Steering Wheel Control Interface Installation Instructions
Prepare for the installation. • If possible, install the SWI-X while you are installing the new head unit. Keep in mind you may need to plug in the factory stereo to locate certain wires; therefore do not complete the head unit installation until the SWI-X is working properly. • Plan a general installation location for both the SWI-X LED and the control body. Keep in mind that the supplied wire harness is two feet long, and the IR harness is four feet long. • Use a multimeter or approved measuring device for checking vehicle circuits.
Read more
2010+ Kia Forte Koup QuickLIFT Installation Guide
Step 1 – Unpack QuickLIFT system and verify contents. Remove all items from the packing tube. You should have the following before beginning: * (2) Gas springs (RT-QL-200-4A) – Be sure to cycle them a few times before installing. * (4) 3/16″ multi-grip #1 rivets (used on hood brackets) * (2) ball-studs and washers * Printed Color Instructions
Read more
